Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Processional torch diameter and base questions *LINK*

Posts

Processional torch diameter and base questions *LINK*

#1

JL

Processional torch diameter and base questions *LINK*

JL

I'm ready to start work on some processional torches. Before I do, I have to decide what is a "reasonable" diameter.

As the poles are wood (cherry to be exact), I don't want them to be "whippy" or bend. The oil-filled candles that will be used for the torches are 1" in diameter.

I was thinking of something on the order of 1 1/4" in diameter. This would accommodate the 1/2" all-thread that will be used to "attach" the candles. I could decrease the diameter if ya'll thought that would work better. I "tested" the acolytes hands and they can all grip 1 1/4" quite reasonably. CM Almy has their long (46") torches at 1 1/4" in diameter. As these torches are going to be similar in height, I was figuring on making them 1 1/4".

In terms of the floor bases, I am going to have to add some weight to them. I was figuring on melting some wheel weights and casting some weights to attach on the bottom of the bases. I can easily drill some holes with a Forstner bit in some scrap lumber and use those holes as molds for the lead.

Does this sound reasonable?

TIA


CM Almy Processional Torches

Re: Processional torch diameter and base questions *LINK*

#2

Re: Processional torch diameter and base questions

Carol Reed, Strawberry, AZ

It all sounds very reasonable, JL.

I use lead shot for base weight as I don't want to get into the stinky business of melting lead. FWIW.

Re: Processional torch diameter and base questions *LINK*

#3

+1 on shot

Dan Donaldson

Mix it with epoxy and pour it into the base.

Re: Processional torch diameter and base questions *LINK*

#4

JL

But I have lots of wheel weights...

JL

:b. I'd have to go buy shot.

Re: Processional torch diameter and base questions *LINK*

#5

Kneale Brownson

Try cutting them into smaller bits...

Kneale Brownson

to put into the epoxy in the base.

BTW, will the kids be carrying the bases or will the torches slide into bases placed where the candles will be stationed?

Re: Processional torch diameter and base questions *LINK*

#6

Since you have the ww's...

John in NM

I'm guessing you have the melting pot, thermometer, and knowledge that goes with them :D

I'd use those since you got 'em, should work fine and be less messy than a bunch of epoxy.

Can't help with the rest of it, only have a vague idea what you're making.

Re: Processional torch diameter and base questions *LINK*

#7

JL

Bases will be stationary by the altar.

JL

Re: Processional torch diameter and base questions *LINK*

#8

JL

I usually cast bullets...

JL

Primary 44s and 40s - though I do cast 50s once in a while.

Re: Processional torch diameter and base questions *LINK*

#9

.32 Winchester Special

John in NM

I only cast for one, but it's a good one :D

Re: Processional torch diameter and base questions *LINK*

#10

Re: Lead

Mark Mandell - Gone Round In Jersey

You do want to "encapsulate" the lead in the bases to avoid contact with the metal's surface by those handling them. Also suggest that your line the sockets with a brass bushing to match up, male/female, with a brass ferrule on the ends of the staffs to give a more durable mount. Plain wood holes will get beat up and sloppy inside of a year's use.

If you don't want to mess with the lead, a 10" piece of 1/2" steel plate scrap screwed to the bottom of your wood base should do just as well.

Re: Processional torch diameter and base questions *LINK*

#11

PS Base Alternative

Mark Mandell - Gone Round In Jersey

I have seen them "stored" by two holes actually drilled in the dais floor with only a brass trim ring above. Nice clean install.