Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Lumber rack question *LINK*

Posts

Lumber rack question *LINK*

#1

Lumber rack question *LINK*

wilbur

I want to install a lumber rack on a cinder block wall. My plan is to get the system that I linked to below. On the wall I plan to attach 2x4's flat against the wall with expansion anchors, which is a method that I've used successfully before, and then attach the vertical lumber rack straps to the 2x4s with lag screws.

The reason why I'm not attaching the vertical straps directly to the wall is that I'm not sure that I'll be able to put the anchors where I want them due to the position of the holes in the vertical straps. If I use a 2x4, I can put the anchors exactly where I want, and the 2x4 will give me more than enough flexibility in positioning the lag screws and the vertical straps.

Because the 2x4's are going to be flat against the wall, I'm limited to using lag screws that are 1-3/4" long at most. What I'd like to know if this is going to be enough to hold the vertical straps to the wall. I will be making sure that the vertical straps are resting on something that is connected to the ground.


Lumber rack system that I'm going to get

Re: Lumber rack question *LINK*

#2

JL

Re: Lumber rack question

JL

I wouldn't worry. I installed a similar system (Triton), a number of years ago. I put my anchors right into my cinder block wall.


I've had plenty of lumber on it since I installed it.

If you are really concerned, go ahead and put up the 2 x 4s. The short lag screws should work reasonably well.

Re: Lumber rack question *LINK*

#3

Re: Lumber rack question

mdclor

Wilbur,

If you are concerned about the holding strength, you could use hardwood 2x4s which will be stronger than SYP. Also, if you will never want to change anything, put some epoxy in the holes before screwing in the lag screws.

FWIW,

Merle

Re: Lumber rack question *LINK*

#4

Re: Lumber rack question

John Lucas

Would vertical storage be better than Horizontal. The reason I ask is I have a lot of wood on a horizontal rack and it's a pain to sort through to find what I want. I'm thinking of converting it to vertical bins. Is there a reason not to do this?

Re: Lumber rack question *LINK*

#5

Re: Lumber rack question

wilbur

Actually, vertical storage is a good idea. At least it's seriously worth thinking about.

The horizontal storage system I was thinking of would give me 5 levels of storage unless I buy more brackets. Adding in more dividers with vertical storage would be trivial.

Re: Lumber rack question *LINK*

#6

Keeping wood flat

Thomas Skaggs, Foothills of Mount Level

I'm not sure of the vertical system you would use but I feel that horizontal storage is better for keeping wood flatter. That's my experience anyway.

Tom

Re: Lumber rack question *LINK*

#7

Re: Lumber rack question

Bruce, a MN Galoot

Just to state the obvious, it costs you nothing to try the vertical first. The only limitation is ceiling height. You can always try horizontal if it doesn't meet your needs. I would go to vertical stacking in my own shop if I had sufficient wall space, but my shop needs compete directly with "garage" needs for what little wall space I have. Canoes, bicycles and camping equipment take up a lot of room.

Re: Lumber rack question *LINK*

#8

Re: Lumber rack question

Hal

The lag screws will be plenty strong in shear, but be sure they are threaded full length for max. pull out strength. Hal

Re: Lumber rack question *LINK*

#9

Re: Lumber rack question

Alan in Little Washington (NC)

If you have the headroom I would seriously consider a vertical rack.

* You don't have wasted horizontal space between individual stacks, so a vertical rack can hold more wood per given amount of volume.

* A vertical rack needs only a fraction of the structure and hardware of a horizontal rack

* A vertical rack doesn't need to be heavy-duty since the floor supports the weight of the wood.

* It can be difficult (and dangerous) to stack, sort, view, and remove boards from a horizontal rack, especially from the high shelves.

* You can easily stack, view BOTH sides, and unstack ANY board in a vertical rack, if the boards are stacked shoulder-style with edges to the wall.

As long as the moisture content is below 20%, boards won't bend according to the USDA Forrest Service Products Laboratory. Any possibility of bending is eliminated if the boards are stowed near vertically



Re: Lumber rack question *LINK*

#10

Re: Lumber rack question

wilbur

Thanks, Alan! Coincidentally, I was just looking at these same pictures that Google directed me to, but these are better because they are bigger.

Can you tell me how long the pipes you used were, and how far apart they are spaced?

Thanks!

Re: Lumber rack question *LINK*

#11

Re: Lumber rack question

Alan in Little Washington (NC)

I used 3/4" galvanized steel pipe mounted in a 1-1/2" X 1-1/2" strip of oak that is bolted to the wall studs. The pipes are 19-1/2" long (18" exposed) and spaced 16" apart. After over four years, the only thing I would change is to lower the pipes a tad, to make it easier to reach the safety chains.

Oh, I forgot to add to my previous post- and who stacks vertically? How about Sam Maloof, George Nakashima, Lonnie Bird, David Marks, Lon Schleining, Norm, just to name a few wood butchers.

Re: Lumber rack question *LINK*

#12

Re: Lumber rack question

Bob Entwisle in NJ

Wilbur, the 2x4 into the wall and lags into the 2x should be fine. (have your boys do a few chin-ups on the brackets to test them, before you commit valuable wood to the rack :D .)

I use a vertical rack of sorts, a wood platform to keep the ends off the concreate slab, and a middle and upper 2x4 horizontally on the wall to attach dividers to. I'm limited by 8 foot ceiling height, but I've got a 2 foot wide x 20 foot long strip of floor on the other side of my garage/Shop that serves as a stack and sticker long board storage area for those few longer than 8 foot boards that come along.

Bob in NJ

Re: Lumber rack question *LINK*

#13

I used those racks,

Ron

but I think I bought them at LV.

My floor is flat, so I cut short hardwood blocks (6") to place under each strap. The blocks bear the weight of each strap, but are only lightly "tacked" (spot of caulk) to the wall (no baseboard in my way). They act as spacers too, so that you know your shelf brackets will be aligned. This arrangement means that the mounting bolts are holding the rack to the wall, but they are not fighting much gravity.

Re: Lumber rack question *LINK*

#14

Built a lumber rack today

wilbur

I have to give big thanks to Alan in Little Washington (NC) for posting pictures of his lumber rack. I completely copied his idea, which was good, because now I see that my original plan to mount horizontal racks would have been less than ideal in many ways.

Here's what I started with -- a big pile of wood that I bought at an auction a couple of years ago. As you can see, I couldn't get to the wood on the bottom or towards the back of the pile at all.


I built a platform out of 2x4s and two pieces of 2'x4' plywood, and mounted a 1x4 board to the wall. I attached pipe flanges to the 1x4 board, and screwed in 18" lengths of galvanized iron pipe that the borg was nice enough to cut and thread on one end for me.

I also attached some 1/2" thick strips of wood to the platform under the pipes to act as an additional stop for the lumber to help keep things vertical.


And here it is all loaded up. The other thing I really like about this project is that I now have my lumber sorted by species.


Thanks for all the suggestions! I'm really happy with how this turned out.

Re: Lumber rack question *LINK*

#15

Re: Built a lumber rack today

Joseph Mulherin, Sr

Very neat job, Wilbur.

Re: Lumber rack question *LINK*

#16

Re: Built a lumber rack today

Dale Penkala

Looks great Wilbur! Glad I checked out this thread. It has given me some ideas for my situation!!!

Dale

Mid-Michigan