Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

Favorite Method for Flattening Panels

Posts

Favorite Method for Flattening Panels

#1

Bart Goldberg

Favorite Method for Flattening Panels

Bart Goldberg

I am always looking for a better/easier way to flatten panels. I would LOVE to have a wide belt sander to do this, but this not the kind of tool that would fit into my home shop. So, I typically use a combination of hand planes, and sanders to do this (usually belt sander followed by ROS). I have considered getting one of those table top sanders (aka Sand Flee), but am not sure if it would work well. What is your preferred method and why?

Thanks

Bart

Re: Favorite Method for Flattening Panels

#2

Re: Favorite Method for Flattening Panels

Bill Tindall

I don't mean this to be a small a@@ answer but my approach is to make them flat to begin with. I flatten the panel lumber if necessary and I am careful at making the glue joints. I will often do only one joint at a time so that I can get it near perfect. If when all is said and done I have a tiny ridge I hand plane or scrape it level.

Re: Favorite Method for Flattening Panels

#3

Re: Favorite Method for Flattening Panels

George Colonel's Workshop-Havertown PA

Hello Bart,

I joint every board first. Normally the only flattening task is to level out the glue joints. For that I use a #3 smoother and a block plane. I also like to use an orbital sander, and mine is an old Skill 1/3rd sheet model. I'd love to have a 1/2 sheet P+C. The larger sanding area minimizes divoting and in-line depressions along the joints. I finish up with a ROS and 220/320 grit.

George

Re: Favorite Method for Flattening Panels

#4

Clint Searl

Re: Favorite Method for Flattening Panels

Clint Searl

1. Flattest boards possible for glueup

2. Biscuits for registration; register from the face

3. Don't overglue or overclamp

4. Hand scrape

5.. Hand sand

Clint

P.S. I bought a Jet 22/44 Pro just for that purpose a couple years ago, but have never used it

Re: Favorite Method for Flattening Panels

#5

Re: Favorite Method for Flattening Panels

Jerry Gibbs

Do biscuits register the surface? They are loose in the slots so they can swell. When the boards are in the clamps, do the biscuits swell in the properly cut slots and overcome the clamps if there is a misalignment?

Re: Favorite Method for Flattening Panels

#6

Clint Searl

Re: Favorite Method for Flattening Panels

Clint Searl

I don't expect the biscuits to force alignment; they just get things started and prevent gross misalignment. I only put a dab of glue in the slots so there's less likelihood of the biscuits swelling. The main thing is to start with flat boards and get the face edgses lined up. Sometimes after they are in clamps, a bit of rubber mallet persuasion is called for. I made a sanding block out of a piece of 2x with rounded ends and inner tube face that takes a 3x21 sanding belt for smoothing the joints by hand.

Clint

Re: Favorite Method for Flattening Panels

#7

Re: Favorite Method for Flattening Panels

Dave Paine

I see some good replies.

I agree that flattening the boards before gluing is sound advise.

I prefer dowels for alignment. Feels more accurate, and I happen to not own a biscuit cutter.

If the boards are the same thickness and the dowels are correctly positioned, then the resulting assembly should be easily finished by ROS.

I happen to have a 16in drum sander and a Flat Master (under the table big version of the Sanding Flea). The Flat Master is good for sanding across the panel. Mine can sand almost 30 in wide. Length means supporting on the infeed and outfeed direction.

I prefer to not need to use the Flat Master if I can get the panel close enough to flat.

I do not have a Jointer hand plane, but this is a common tool to get a panel flat after gluing.

I do use a 5in ROS and a 1/2 sheet (4.25 x 11 in) ROS sander if needed.

Re: Favorite Method for Flattening Panels

#8

Bart Goldberg

Dowels?

Bart Goldberg

I've never tried using dowels for panel glue ups. In fact I don't use dowels for anything nowadays as there seems to be better methods for most of the things I might want to use dowels for. However, I do think if you use dowels correctly, they have much better alignment ability than, say biscuits. What type of jig do you prefer to use for dowels?

Thanks

Bart

Re: Favorite Method for Flattening Panels

#9

Re: Dowels? *LINK*

Dave Paine

For panel alignment I use the simple Self Centering jig. Link below is Lee Valley, but this item is sold by many stores.

Steel screw and aluminium body. Replaceable steel inserts for smaller dowel holes.

I have found using dowels to be less effort than e.g., routing a slot on both pieces and planing a strip of wood to fit.


http://www.leevalley.com/US/wood/page.aspx?p=32250&cat=1,180,42311,42319&ap=1

Re: Favorite Method for Flattening Panels

#10

Re: Dowels?

Dan Donaldson

For edge gluing as in panel building, I find it easiest to not use any biscuits, dowels, or any other alignment aids. If the boards are any kind of straight, they are not necessary, and it is possible to line the boards up as you clamp them. Any error in the placement of the dowel or biscuit is permanent and cannot be corrected.

Re: Favorite Method for Flattening Panels

#11

Second the motion...

doug f, san clemente, ca

I have never used dowels or biscuits for panel gluing; the cons always seem to outweigh the pros.

With straight boards, milled square and parallel, gluing a panel is not that tough; straighten as you glue, maybe use a caul or two if necessary and plane or sand any minute differences.

At least it works for me.

Doug

Re: Favorite Method for Flattening Panels

#12

About that sanding block....

Tim Greif - West of Chicago

I'd love to see that. How did you rig it to snug up the belt?

Re: Favorite Method for Flattening Panels

#13

Clint Searl

Re: About that sanding block....

Clint Searl

Block with a piece of inner tube contact cemented to one face


Block with belt mounted and tightened with opposing wedges. I exagerated the wedges here for visual effect.


Re: Favorite Method for Flattening Panels

#14

Bart Goldberg

Panel Glue Ups

Bart Goldberg

Doug,

I agree with you - that has been my experience as well and I have not used any alignment or registration mechanisms in many years. I've never used dowels, but I have seen problems with Biscuits where the wood around the biscuit swells from the glue, and if you sand to soon, you end up with indents at the biscuit locations after the wood swelling goes down.

Thanks

Bart