Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Your experience learning to spray?

Posts

Your experience learning to spray?

#1

Your experience learning to spray?

Bill Tindall

For the benefit of someone just starting, how did you learn and what equipment have you tried successfully or not?

Someone showed me and I have only ever used a professional Binks or DeVilbiss gun. Are there useful books? A mentor certainly would be helpful. Maybe some local woodworker or someone at a local cabinet shop would demonstrate. Oddly there are classes on every detail of woodworking but not spraying a finish.

Will a cheap spray gun yield success in the hands of a beginner?

There are variables that are important that are hard to explain in words. The following applies to conventional guns which are easier to learn on.

1.The pressure at the gun needs to be optimized. Too little pressure and the spray comes out in too large droplets. You can see these large splats on a practice target. Too little and a fog comes out with poor transfer efficiency.

2.The viscosity of the finish needs to be some minimum value or the finish won't suck up in the gun. This is more a problem in thinning oil paints enough to spray.

3.The feed rate needs to be adjusted so that a moderate coating is applied. Too high a feed rate and there will be runs.

4. Finally, the distance of gun from target is important, again for transfer efficiency.

5. I think most important is good lighting so you can see the film as it hits the target.

I can teach someone the mechanics of spraying in minutes, or you can teach yourself. Get a piece of cardboard and fill the gun with colored water. Spray to get a uniform overlapping coating. Each pass should half lap the last pass. It is the other parts that a mentor would be handy. Spraying on a practice surface might be all that is required to get down the basics. Sometimes I just spray at something flat to see how the coating is laying down before I begin.

Lacquer is very easy to learn to spray. It is formulated so that its viscosity steeply increases as the solvent evaporates (4th power of solids concentration for those mathematically inclined). Hence, runs are uncommon. Paint is prone to run but it is the easiest to learn to spray a uniform coating because it is easier to see the result, than on a clear film. Water based finishes are the hardest to spray in terms of run potential. If you can spray water you can spray anything.

Re: Your experience learning to spray?

#2

Re: Your experience learning to spray?

Jesse Cloud

Bill, I think you have identified an opportunity! Its true that spraying classes are few and far between. Why don't you offer one? Might be quite a money maker!

Re: Your experience learning to spray?

#3

Re: Your experience learning to spray?

doug f, san clemente, ca

Bill - when Enduro finishes used to be headquartered right here in San Clemente, they offered day long finishing classes, primarily spraying their product, but with several other techniques demonstrated.

Though the classes were not cheap, IIRC about $85 for the day, there was always a waiting line to sign up.

Yes, it could be a good opportunity.

Doug

Re: Your experience learning to spray?

#4

My classes are free

Bill Tindall

Show up with something you want finished and I will show you how. Money back satisfaction guarantee.

Re: Your experience learning to spray?

#5

Re: Your experience learning to spray?

Robert R. Clough

Bill, I learned by trial and error, error, and error. (called experience, I think) I have used standard spray guns occasionally but usually I have used spray cans. They are not always the easiest to use but at least the spray is consistent. I did have an inexpensive pulse spray gun years ago that worked quite well. It was not up to really heavy work though - it gave up and died!! I agree the major trick is viscosity.

I now have another inexpensive spray system - Rockler sells then as does Harbor Freight. Got it last year and have not tried it yet. I expect to use or try to use it soon with water based poly and then with water based paint. I have to do a second coat on an outside wall of the garage. If I remember and you wish I shall let you know how it works. Please e-mail me rclough57@wi.rr.com

Re: Your experience learning to spray?

#6

From a Pro

Mark Mandell - Gone Round In Jersey

As a kid in high school I got into building custom car models. Local kids would enter into contests sponsored by various outfits and then the work would be judged by several pros. I won several prizes and got invited to several customizing shops. There I got shown how to apply the real finishes that I had only hinted at with my "Testers" rattle cans. I got good enough at it that the summer after my junior year I got a part-time job in one shop as a "base coater" putting on the foundation colors.

After that, applying wood finishes is pretty easy.

Re: Your experience learning to spray?

#7

PS

Mark Mandell - Gone Round In Jersey

I still have my old Craftsman siphon/pressure feed 50psi gun, but as I went from solvent to waterbornes finishes, I migrated to HVLP. First set was a Fuji 3-stage turbine gun I bought used for $300. Noisy, hated the bleeder, and the gun got hotter than a pistol. Sold it for $200 and put that towards a pressure pot set up running a Walcom HLVP FZ SP; will lay down medium and light body clears like glass with only 12 psi.

Needed a small gun for when I didn't want/need the whole pot routine. Tried one of those $20 touch-up guns (HF and others) but not pleased with the atomization or the pattern. Snagged a CA Tech. mini top-cup HVLP gun, which I use for small items and is great for spraying turnings both on and off the lathe.

Re: Your experience learning to spray?

#8

Clint Searl

Taught (sorta) myself

Clint Searl

....in '74 with a Sears push-me/pull-me gun and auto lacquer from a pamphlet put out by one of the paint companies. Then got a DeVilbiss detail gun. Still have both guns, but now use a couple DeVilbiss gravity feeds and a gravity feed Sata detail gun from a 5HP IR compressor. Nothing but solvent one part lacquers. I eyeball the viscosity, flow, and pressure, so my technique may be unorthodox, but serves my specs.

Clint

Re: Your experience learning to spray?

#9

David Barnett

Being taught vs. at-home: Airbrush University *LINK*

David Barnett

I'd say that's a pretty good deal, Bill.

Long ago, I learned airbrushing for design and illustration, which I enjoyed. Decades later, for larger things, I learned from a pro who'd worked for Electric Boat for too long, claiming the most exciting thing that happened was when he got to change paint colors once. Left, worked for furniture manufacturers in NC before he finally struck out on his own, which found him freelancing and occasionally teaching at a New England woodworking school.

I started with conventional compressors and guns, which was straightforward enough, then had a brief foray into HVLP, which I didn't take to at all. I sprayed off and on for a couple years while I had access to professional equipment and spray booths but never really liked it or the finishes. When I developed severe respiratory problems, that ended.

I'll admit, there are some things that simply must be sprayed, such as my vintage B&L SK universal boom stand -- 66 lbs of enameled iron, stainless steel and aircraft aluminum (these brutes used to cost the government as much as a new car). Do I leave it two-tone grey or go for the chartreuse metal-flake? Decisions. Seriously, my kiln won't handle anything even half this big, so it's going to get sprayed.


While one can learn spraying in short order (I did), I've seen some work that blows me away, although that's mostly outside furniture finishing. I can definitely appreciate the skill and work. As for furniture finishing and luthiery, if that's the look you want, I can definitely appreciate the ease and speed.

Now if someone really wants to make a big thing of it, if they love the joy of extreme autodidacticism, for sheer overkill I doubt there's anything to compare with Airbrush University, a home-study subscription series of 78 rental DVDs entirely devoted to (mostly automotive) spraying, spraying, and more spraying. At six DVDs a month, say, in just over a year... :)

I think your one-day crash course is the way to go.


Airbrush University (Smartflix)

Re: Your experience learning to spray?

#10

Re: Your experience learning to spray?

Howard Acheson

I was a part owner of a large cabinet making/furniture woodshop. We had 1 1/2 full time finishers, multiple equipment and an 10'x10' finishing room/booth. We frequently had an apprentice finisher which accounts for the "1/2" person. Our apprentice program ran about a month depending on the student. Of course, it started out very intensive with learning the basics of "reading" the spray, making adjustments to the spray and pattern and learning the techniques required. The apprentice started out spraying water onto cardboard boxes and then graduated to spraying various finishes onto cardboard and scrap wood. He also learned surface preparation even though that was the primary responsibility of the cabinetmakers.

It was generally a week of more before the appentice was allowed to spray projects. He was almost continually under the supervision of our best finisher. As he become more competent he was shown how to handle problem and refinishing techniques. After 3-4 weeks he was almost on his own but our top finisher kept an eye on him for a couple of months.

The best book I have seen on finishing is Charron's Spray Finishing. Jewitt's Taunton Illustrated Guide to Finish has some good info on spraying.

Re: Your experience learning to spray?

#11

Re: Gee, been a long time ago

Larry Clinton At Frankfort, (Central) Indiana

I started spraying bicycles in the 1940's with spray cans. Around 1958 I sprayed my first car with a gas powered compressor and a decent old Binks (as I remember) spray gun. I currently have a fairly good Binks conventional spray gun with a good 60 gal compressor, fitted with a standard filter, and additional vapor/water filter. I also have several cheap conventional guns and some HVLP (conversion) Harbor Freight guns along with a couple of air brushes. I spray everything from Behlen lacquer (one of my favorites) to implement paint (have a couple trailers and an old Ford 9n tractor). I also have sprayed shellac and Minwax poly (thinned about 50/50. I do not use any waterbased finishes guess I am to old and stubborn to change. I really don't care for the HVLP except for spraying the inside of items that are closed like chests - shelves etc. It seems to lay down more finish with less blow back in your face. Course that opinion could be due to the fact the equipment I have for the HVLP is not anywhere close to the quality of my Binks conventional. The ONLY issue with conventional spray I have found is the loss of finish due to over spray. I think it is the easiest technique to learn and use. I have taught my youngest son to spray and he is now as proficient as I. One of the biggest factors that is hard to to get through to first time users is that you can't cover an Item with one coat. It is hard to understand that the second and third coats will fill out the color and smooth the finish. I also tend to thin more than really necessary and spray multiple coats. When using oil based finishes I use various solvents including Acetone, turpentine, Naphtha, and mineral spirits dependent on the temperature and humidity in order to achieve the best "flow" and drying time.

Re: Your experience learning to spray?

#12

Clint Searl

Re: Gee, been a long time ago

Clint Searl

Larry, I had a 9N Serial#9284 from '39 till I replaced it with a Kubota. It needed considerable restoration, but I'm sorry I let it go.

Clint

Re: Your experience learning to spray?

#13

David Barnett

I recommend... *LINK*

David Barnett

"You don't have to say anything and you don't have to do anything. Not a thing."

"Oh, maybe just whistle. You know how to whistle, don't you, Steve?"


"You just put your lips together and blow."

Re: Your experience learning to spray?

#14

I observed our Tom Cat

George@Colonel's Workshop-Havertown PA