Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Trim Carpentry help?

Posts

Trim Carpentry help?

#1

Trim Carpentry help?

Paul Woolson

Hi all. I'm attempting to add oak quarter rounds to our baseboards. All is going well except I came to a transition where the floors are different levels. They are 1/4" off from each other. This is only a span of 6" where the quarter round needs to go so there really isn't any way to flex it and cheat.

Does anyone know how this should be done? Thanks, Paul

Re: Trim Carpentry help?

#2

JL

Re: Trim Carpentry help?

JL

Scarf joints and coping saws are your friends in trim carpentry (sandpaper also helps).

I don't know what is acceptable to you. But one thing to think about - if you cut a scarf joint so that the diagonal of the "higher" piece falls over the diagonal of the lower piece, you can minimize the appearance of the transition. You can also put a thin wedge of material under the lower part to build it up.

Re: Trim Carpentry help?

#3

Re: Trim Carpentry help?

John Veerkamp

If the higher piece is only 6" long I'd trim 1/4" from the bottom of the short piece. That way the eye will see a level line and not the height difference.

Re: Trim Carpentry help?

#4

Re: Trim Carpentry help?

Paul Woolson

Ok, I wasn't clear.

I would have no problem taking material off of the taller floor area. BUT...there is quarter round on that level also. This is the main problem, there is quarter round on both levels that I need to meet up with. This floor change is literally right down the middle of the house. So one level of trip is 1/4" lower than the other. Yet I have to find a way to transition them. Does that make more sense?

Re: Trim Carpentry help?

#5

A drawing might help

Bill Houghton, Sebastopol, CA

Jerome's (JL's) suggestion is consistent with traditional practice. When you have a level change, if you can't otherwise make it work, a 45 degree angle transitioning down to the lower level is considered acceptable. I might soften it - sand it kind of rounded - rather than doing a sharp 45.

Alternatively, consider something HIGHER than the 1/4 round that the lower 1/4 round can die into (butt against).

Again, a drawing would help. Words are limited in describing visual stuff.

Re: Trim Carpentry help?

#6

Re: Trim Carpentry help?

Paul Woolson

Ok, here's a drawing. Imagine you are in a doorway, looking at the left "wall" of the opening. That's what I'm dealing with. I've shown the two quarter round on each side of the short "wall". They are both cut at 45�. The red lines are the piece I need to somehow create. And you can see the difference in height on the floor.


img

Re: Trim Carpentry help?

#7

Re: Trim Carpentry help?

Bob Entwisle in NJ

How about something like this?


Re: Trim Carpentry help?

#8

Re: Trim Carpentry help?

Bill Houghton, Sebastopol, CA

I'd modify Bob's suggestion to have the top have a straight line, from the top of one quarter round to the top of the other.

The geometry of this will be difficult, but with a block plane, sandpaper, and some experiments, you might be able to do it. I hope this will be painted, rather than stained; you can cover up lots of fudging with paint.

Re: Trim Carpentry help?

#9

Re: Trim Carpentry help?

Lee Schierer McKean, PA

Make a wedge about 3-4 feet long that is 1/4" high at the tall end and 3/4" wide to match your quarter round. Loosen the last three to four feet of the piece on the left side of your drawing as slip the wedge under it. Now the ends of your quarter round will be at the same height at the top. Make the piece on the end wall match on top and scribed on the bottom to match the floor.

Alternatively you could make the wedge on the left wall only 1/8" tall and trim down the height of the piece on the right wall about 1/8".

Lee

Re: Trim Carpentry help?

#10

Re: Trim Carpentry help?

R. Payne

Based on this picture, I think I'd put a decorative break between the two pieces at the split. It could be as simple as a block or as fancy as you want.

ron

Re: Trim Carpentry help?

#11

I like this one

Dan Donaldson

Put something entirely different there so it will not look like you tried to match and failed.