Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

An epoxy question

Posts

An epoxy question

#1

An epoxy question

Gary Camp, Bend Oregon

I have a 3-0 six panel solid core door I want to put in my barn. The door was standing under the barn eve when I bought the property and has suffered some weather damage. The doweling in the joints is sound, but there are some open areas between the stiles and the rails and some checking in those same areas. I was wondering about the feasability of squeeging some expoxy glue or now that I think about fiberglass resin into the joints and cracks. I want to fill the cracks and splits and add a bit of strength and stability to the joints. Does this sound like it might work or am I doom to failure, I have a lot more time than money, and I don't really have that much time.

glc

Re: An epoxy question

#2

Re: An epoxy question

FredD

If as you say , the dowel joints are still intact , why not fill the cracks and splits with a Exterior Spackle and paint with a good grade of Exterior Enamel or alternatively go with a Stain and some Spar Varnish?

FredD

Re: An epoxy question

#3

Clint Searl

Bondo

Clint Searl

Re: An epoxy question

#4

Re: An epoxy question

Keith Newton----Little Rock, Arkansas

Gary, I always keep epoxy on hand, and probably have used over 100 gallons of it, but I don't think I would use it as you stated. If you can take the door apart and want to use epoxy to re-assemble it, that would be my choice.

But if you can't get it apart, the epoxy is to viscous to really get into the cracks very far. I would use Cyanoacrylate instead. It is thin, and will flow into cracks that you can't even see, and penetrate the cells walls making it plastic. Epoxy is long chains of molecules too large to penetrate, so it really won't get in very far.

When you say or getting some fiberglass resin, that is what epoxy is. There are others too, like polyester resin, or vinylester resin, but epoxy is one of the most commonly used.

You can get a lot of additives to thicken or change the properties, like if you need to fill large cracks. But just mixing the dust from a sander bag will work.

Re: An epoxy question

#5

Re: An epoxy question

John in NM

If it's for interior use, I'd try bondo, maybe... or just a good filler followed by paint. Of the resins I've used, bondo and the polyester resins for fiberglass are the worst for wood adhesion. West System epoxy is thinner and has better adhesion. Recently I've been using urethane resins for duplicating plastic parts, and some of them are very thin and seem to stick to everything but silicone. However, they're probably more than you want to spend for this project, and do not have a good shelf life for the 90% you'd have left over.

For exterior use, I'd get a new door :D

Or maybe try a good filler and paint, then if the filler pops before you're mentally ready to repeat the job, get a new door at that time.

With all respect to Keith, I'd avoid CA glue. The word is moisture from the wood decays CA over the course of a few years. While wood filler might not even last that long depending on exposure, you also might get a lifetime out of it - just too many variables for a good prediction. Many fewer variables with CA - moisture = failure, the amount of moisture = amount of time to failure. Not a good gamble.

Re: An epoxy question

#6

Re: An epoxy question

Jesse Cloud

If you use epoxy, give it a good coat of paint. UV just eats epoxy up at higher altitudes.

Re: An epoxy question

#7

thank you

Gary Camp, Bend, Oregon

Good afternoon, thank you for all the responses. I generally try to reuse rather than buy new so that is what prompted my questions. The door in question is going at the top of an interior stair landing on the second floor of my barn, so it really is an interior application, not much sun. I was thinking epoxy to add a bit of strength to the rail / style connection (even though there is no flex in the joint). I realise that fiberglass resin is an epoxy, I tend not to think of it as an adhesive. I mentioned it because it is available locally, where as the nearest West Systems is a 100 to 160 miles away. It sounds as though West Systems maybe the way to go, however I have not priced the product or shipping. I could buy a "cheesy" hollow core flat panel door for about $70 but I really want a door that is a bit more soild and I'd like to conserve resources where ever possible. I guess the Habitat Restore may be an option also. as is Durhams rockhard putty.

Thanks again

glc