Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Raising the UNDERSIDE of the roof???

Posts

Raising the UNDERSIDE of the roof???

#1

Kneale Brownson

Raising the UNDERSIDE of the roof???

Kneale Brownson

I have a garage with eight-foot walls and trusses. I'd like to alter the bottom of the truss system to create a space with at least a couple more feet of height.

The 2 X 6 trusses are 22 feet across and the peak is 10 feet above the bottom of the crossmember. The 2X4 bracing is six feet in from the crossmember ends and three feet below the peak. I'd like to add a new crossmember about three feet above the existing one for all but the two trusses at the gable ends and then eliminate the lower crossmembers.

The sketch shows approximately what's there now and a dotted lines of what I'd like to do. Can I do this? Should I add additional angled bracing?


img

Re: Raising the UNDERSIDE of the roof???

#2

Maybe

Bill Houghton, Sebastopol, CA

Trusses are engineered - meaning that the engineers used as little wood (thickness/width) as they could to support the roof. Cutting out truss members may or may not work - and you would find out which when your roof did or didn't sag and fail.

If you know what company did the trusses, you might contact them to see if they can recommend an in-place modification that will do what you want without risking component/roof failure.

Re: Raising the UNDERSIDE of the roof???

#3

Re: Raising the UNDERSIDE of the roof???

FredD

Kneale, contact a structural Engineer before you destroy your roof.

Cutting a Truss anywhere I have worked is illegal without a Engineer signing off on it .

What your contemplating will remove the few tension and compression struts you presently have and transfer the roof load which is now on the wall to the Rafter part of the Truss which is another no -no in construction wherein you cannot legally cause a roof structure to carry the load of a Joist system.

One thing you can count on, the roof structure as contemplated will fail with the first snow or wind load.

FredD

Re: Raising the UNDERSIDE of the roof???

#4

JL

Re: Raising the UNDERSIDE of the roof???

JL

Contact a structural engineer and have him or her design a suitable truss.

I've seen scissors trusses in a similar situation - but they were designed for that particular job. Essentially a "vaulted" ceiling in a garage. It made the space really light and "airy".

Re: Raising the UNDERSIDE of the roof???

#5

Re: Raising the UNDERSIDE of the roof???

Galen Vetterick

I agree with the others on having soemone design your truss changes. It might be possilbe to make sissor type trusses out of what you have before you cut out materials. You don't say where the truss sits on the cap plate. Is there no eave or does it rest back in on the lower chord some distance. Your scketch to the eye makes it look like your new lower chord is higher up than 3 feet if the 2x4 upright is 6 feet in. Till you say where the truss bears on the wall other modifications may be possilbe.

Re: Raising the UNDERSIDE of the roof???

#6

Kneale Brownson

Re: Raising the UNDERSIDE of the roof???

Kneale Brownson

Trusses rest atop the walls full width.

Between the two upright 2X4s is a 10-foot space where currently there is a plywood deck. I'd gladly give up that almost useless "storage" space in favor of additional bracing both upright and across.

I definitely wouldn't be doing anything without an engineer's advice, just wondered if the brainpower here might suggest approaches.

Re: Raising the UNDERSIDE of the roof???

#7

Re: Raising the UNDERSIDE of the roof???

Barry Irby

You've gotten the correct answer. The trusses were Engineered to start with and you should not modify them without having them re-engineered.

It can probably be done, but it depends on the loading (snow and wind) and on what materials were used to start with. If the rafter or top chords are 2x6's or larger and not joined in odd places then it might be fairly easy to do exactly what you want. But, it's up to the Engineer. He will design the connections and tell you what material to use. He is the one responsible for the work, so he may over Engineer it to protect both you and himself.

On one of my Home Inspections i saw a house where they had cut out all the interior webbing in the trusses and just left it. The roof was so sway backed the house looked like a pagoda.