Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

Any Maloof rocker makers out there

Posts

Any Maloof rocker makers out there

#1

Jim in Burlington Ont.

Any Maloof rocker makers out there

Jim in River Oaks, Ont.

Hi,

Last fall I revisited my list of "Must Make" projects, I included a Maloof like rocker on my schedule. I see it as a marque piece and I know I will enjoy the process.



I have some resources available to me in terms of construction etc, I think I am going to make it in cherry as I have a decent supply of air dried 8/4 figured stock. Just curious if there are others out there who have made one or are making one, perhaps we could share notes etc.

Take care,

Jim

Re: Any Maloof rocker makers out there

#2

Re: Any Maloof rocker makers out there

Doug Reynolds in Seattle

Jim: I started one at the Marc Adams Schhol of Woodworking a couple of years ago and have the plans, patterns and video from www.haltaylor.com. Unfortunately, I have never finished mine. It is still on my "To Do" list. I just got a load of 12/4 figured walnut from an instrument maker who harvested it about thirty years ago. So, now I must get busy finishing one and making another.

Re: Any Maloof rocker makers out there

#3

Re: Any Maloof rocker makers out there

Harry Ludke

I've made 5 Hal Taylor rockers over the past few years. One out of Walnut, three Cherry and one Ash dyed and stained a antique black. Their not quite the same as Sam Maloof's chairs, but the look and process is very similar. They were very challenging to build but I had lot's of fun making them.

The First rocker (prototype) takes the longest since you have to make all the jigs and understand the process, learn from from your mistakes ect. After that, each rocker took about 100 hrs to make. After the first few, I realized that it's easier to work on two chairs at a time. A fair amount of time is taken up with jig setups. So you might as well makes the cuts for two chairs instead off one. Efficiency and all that!

Be prepared to do LOTS of freehand sanding. My Milwakee 4" grinder became my best friend. I also have a pneumatic drill that I attached 2" sanding drum sleeves to. Great for feathering in transition joints.

Good luck, and enjoy making your family heirloom .

Re: Any Maloof rocker makers out there

#4

Re: Any Maloof rocker makers out there

Denny Watson

Jim,

I haven�t posted here before, but maybe I can add a note for your question. I made a Maloof style low back chair from cherry using the plans of Charles Brock (which I can recommend). Thought a lot about cherry versus walnut. Here are a couple of photos taken right after it was finished with the (Sutherland Wells) tung oil purchased from Lee Valley. Cherry finished this way will have chatoyancy � when light hits the surface, the wood will appear darker or lighter depending on the light angle relative to wood grain direction and viewing angle. The new thing I learned is that because grain direction will usually change at the joints, in some lighting situations, the wood will appear darker and lighter on either side of the joint. Thus, the joints, regardless of how well matched, will in some light be quite visible as joints rather than just a continuous flow of curving wood.

This (chatoyancy effect) is hard to show in photos. I like the cherry version and the finish, even more as it darkens with age. Seeing the joinery is not necessarily a bad thing. I had to get used to the idea that in some light and at some angles, the joint lines will be more visible with cherry and probably less so with walnut. I�ll probably follow this with a rocker and probably stick with cherry. Be glad to share experiences.




Re: Any Maloof rocker makers out there

#5

Re: Any Maloof rocker makers out there

Jesse Cloud

Great job Denny. You really nailed the figure on the crest rail!

Re: Any Maloof rocker makers out there

#6

Re: Any Maloof rocker makers out there

Bruce, a MN Galoot

Very nice job! I recall reading an interview in which he said that it's one thing to draw a line for a curve and quite another to make it mean something. You did good!