Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Picture Frame Clamp the best??

Posts

Picture Frame Clamp the best??

#1

Picture Frame Clamp   the best??

del schisler

I am looking at getting some picture frame clamp's. I have looked at some on line. Any one have used these and have a good one that work's . I want one that tighten all 4 corners at once. Not the one that only does the 1 corner at a time. I do lot's of framing now and i been using the web clamps. With the web you can's see the corner's. I make the corners very good. I would like to see them any way. With the corners of the clamp so that the glue has a place to go and not just in the corner clamp. After a while i would guess you would have to clean them out?? thanks del

Re: Picture Frame Clamp the best??

#2

Positive and negative recommendations

Bill Houghton, Sebastopol, CA

I would not recommend, from my limited use of it, the type of frame clamp pictured in the link at http://www.rockler.com/product.cfm?page=725, with two sets of two arms held together with a short piece of something, pulling together in a kind of X layout. I found it awkward to use, and not very effective.

I've been happy with the clamps that are an aluminum extrusion with a 90-degree fence and two little clamping bars tightened with screws, like those at http://hand-tools.hardwarestore.com/67-403-other-clamps/adjustable-corner-clamps-600034.aspx. But I haven't experimented with all the different kinds; I use these because they show up at garage sales cheap.

Re: Picture Frame Clamp the best??

#3

Del, I'm with Bill on the "X" clamp

Gary Smyth

every time I try to set mine up I quit and find an alternative. It is hard to adjust and you have to do a dry run each time, even if the frames are the same size, it's so slow the glue will set before you get it right, and once put together you have to disassemble it to get it stored as it won't fold as you might think it would. Truly a waste of money.

The best clamps I've found for me are European by Ulmia. They are spring steel in at least two thicknesses/strengths. Not cheap and they will leave a small mark on each frame edge, but they work where other clamps will not do as good a job. These do not do all corners at once as you asked.

The other alternative would be a web clamp. Bessey VAS 23 works too. All the miters have to be near perfect though for it to be of value.

Re: Picture Frame Clamp the best??

#4

I'll second Bill's second opinion

Charles Yawn

I have a set of four of the aluminum clamps in Bill's pic. Used them occasionally and am satisfied with their ease of use and clamping ability. You do have to be careful about marring the frames surface with the small clamping surface of the clamps, use pads.

Charles

Re: Picture Frame Clamp the best??

#5

Re: Picture Frame Clamp   the best??

AZ in Colorado Springs

I've used the Rockler miter vise, part # 36474,a number of times. Works great. A little expensive (I use them at the Air Force Academy arts and craft center so I don't have to buy them), but with four of them, you can glue up the whole frame at once.

Re: Picture Frame Clamp the best??

#6

David Barnett

Every version of that miter vise... *LINK*

David Barnett

...I've seen is well made and works great. I got four of those when I had a bunch of same-sized frames to make but only use one-at-a-time now (four only fit so close together, anyway). Versatile and fast. If you don't own a trimmer and all the other framing gizmos, this lets you saw through the last joint for a tight fit (use a very thin-blade saw -- dozuki, etc.).

I know someone who really likes the Lee Valley Veritas� 4-Way Speed Clamp, especially on small to medium frames.

http://tinyurl.com/4-wayFrameClamp

Prices are all over the place on the miter vises. I got mine for less than $40 each. Rockler wants $83.49.


These guys want $34.95 each when you buy four

Re: Picture Frame Clamp the best??

#7

thanks for reply's  the best pic. frame clamp??

del schisler

Re: Picture Frame Clamp the best??

#8

Re:my favorite frame clamp

Carol Reed, Strawberry, AZ

can be found here: http://www.harborfreight.com/corner-clamp-with-quick-release-38661.html

$8 on sale

I like the quick release feature and the 'bar' shaped clamping pads. When faced with multiple same sizes, I screw two of them down co-planer to each other. That way I clamp against a fixed point to square the assembly. I even use them to hold cabinet and book case sides and ends together for assembly.

Re: Picture Frame Clamp the best??

#9

I disagree, these are fine with some tips

Grant in Iowa

I have five of this type of clamp and after beign frustrated with them at first, I now prefer them.

When I first tried to use these, I was indeed frustrated with them for the same reasons others mentioned.

I overcame those issues, and now use them extensively for assembling picture frames.

The issue with the fiddly nature was resolved by removing the tightening mechanism and simply using a small clamp to tighten the to the work. This gives a greater range of motion and reduces the need to adjust the corner blocks on the frame.

I also had an issue with tiny gaps on each corner appearing on the tops of each frame corner as the clamp frame was tightened. I resolved that by sticking a business card beneath the outer end of each corner block to slightly elevate it.

The closed corners haven't been an issue at all, as the plastic doesn't adhere to glue and it actually works to your benefit to align things as the clamps are tightened.

Fiddly, I know, but they do produce good, fast results. I have five sets and can continuously turn out flawless frames as needed.

FWIW,

Grant in Iowa

Re: Picture Frame Clamp the best??

#10

Rick L

Re: Merle *LINK*

Rick L

While there are many clamps out there the Merle is the best for your criteria in my 40 years of experience. The metal band puts it far above the typical band clamp and makes it easy for one person to clamp frames. I've tried them all and only keep a minimum of the better clamps in my shop. The less tools and knowing how to use them to the max is my motto.


Merle Miter Clamp