Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

WC Weekend Accomplishments.....

Posts

WC Weekend Accomplishments.....

#1

WC Weekend Accomplishments.....

Dennis E Peacock

4 Apr 2011

Good Morning,

Been a stormy morning here with thunderstorms and strong winds, but hey, that's just the way it is here in spring time.

After a several uses of the Kraut forks, the LOML and the LOML Jr. like them as the design works well so this one design will be a keeper. I'm pondering on a different design for the typical form of a fork for a more common use.

Been doing a lot of work in the yard since the weather has been nice. Now that my back is much better, working in the yard was much more enjoyable. Man, I sure do hate back problems.!!

The LOML Jr and her fianc�e got baptized yesterday and we took off from our normal church service to attend and share that time with them. It was a special time for all of us and we are very proud of them.

Well, that's it for me, so what did YOU do this past weekend.??

Best of weeks to you all.

Dennis Peacock

Re: WC Weekend Accomplishments.....

#2

Jim in Burlington Ont.

Sunny Days

Jim in River Oaks, Ont.

Had fun with my pup!


Nothing like your favorite stick and sunshine, a perfect combination

Take care,

Jim

Re: WC Weekend Accomplishments.....

#3

A Mixed Bag

Mark Mandell - Gone Round In Jersey

Had planned on a trip with Memsahib to Willard Bros. to pick out a live-edge slab for her new coffee table. Even prepped her for the prices we were likely to see. Trip got adjourned at the last minute so I decided to spend the time taking care of unfinished business in the shop.

Job 1 was to sort out the shorts bins that have been accreting for some 10 years without withdrawals. Slice and dice and we had a nice evening's fire of cherry, walnut, ash, and oak.

Job 2 was hanging the doors on a smallish maple credenza that SWMBO had commissioned for the master bath, but then decided not to use. Made the mistake of trying to put nickel-bronze screws into hard maple, even with predrilling and beeswax. Two snapped off nicely below the surface. Asked a friend for an extractor but he only had the reverse thread type. Mentioned my dilemma in a call to Ellis and he reminded me about tube-type screw extractors. Went back to the shop and made one with some 1/4" drill rod. A bit crude on the teeth, but it worked just fine

so the holes were filled with some dowel and the hinges got mounted with steel screws. Now to make the top and get ready for the finishing days to come.

Job 3 was to get the air suspension system for my Stubby lathe redone. Got the new HDPE plate cut and the new lifter holes drawn. Now on to the fly cutter.

All-in-all, not a bad couple of shop days.

Congrats on your baptisms, Dennis.

Re: WC Weekend Accomplishments.....

#4

Next time

Lee Schierer McKean, PA

Try lubing the threads of your screws with beeswax to prevent the breakage. If you go visit a local beekeeper you can get a chuck that will last a lifetime for nearly nothing and you could also pick up a pound or two of honey while you are there.

Lee

Re: WC Weekend Accomplishments.....

#5

Re: No Next Time

Mark Mandell - Gone Round In Jersey

Tried that, Lee. My chunk of beeswax dates from about 1975. ;)

Would have rathered the screws matched the hinges, but the apparently cheap alloy on the supplied examples would take next to nothing in the way of torque even putting them in by hand.

m

Re: WC Weekend Accomplishments.....

#6

Varnish(es)

paul in AZ

Working on a table on sat. I belatedly realized that there was not enough varnish left for the next coat I was about to put on. So, rather than running out to get some more I thought I'd try some gel poly that I'd picked up on a whim. It goes on easy enough but I was not pleased with the result. It takes forever to set up and the coat as I applied it wasn't even. Fortunately woodcraft is open on sundays so I could get some of the General I am used to. A little buffing out then a new coat and I got a much more even result.

I'm perfectly willing to concede that the problem is with me and not the gel. I may even learn to use it some day.

Whatever, I suspect it is a better product for small objects and not for large surfaces.

One last run through my taxes and picked up a couple of minor errors. Funny that as good as the software is it doesn't pick up erroneous data entries. GIGO.

Re: WC Weekend Accomplishments.....

#7

Jason Roehl in Lafayette, IN

Another step...

Jason Roehl in Lafayette, IN

...to what you did would be to first run in a steel screw of the same size, then remove it and install the brass screw.

Jason

Re: WC Weekend Accomplishments.....

#8

Interesting Idea

Mark Mandell - Gone Round In Jersey

I'll have to try it on a piece of scrap.

Re: WC Weekend Accomplishments.....

#9

Ellis Walentine

Family stuff

Ellis Walentine

It was a regrouping weekend for us, staying around the house on Saturday, working on the final prints for our upcoming kitchen remodel, yard work on Sunday. Not much in the way of woodworking, although a nice sized cherry tree came down a week or so ago and I started a big spherical vessel from a section of the trunk. It turns like butter.

Ellis


Re: WC Weekend Accomplishments.....

#10

Jesper, Denmark

Re: #2 problem........

Jesper, Denmark

Working with black locust in the boatyard, this was the standard procedure with bronze screws:

Pre-drill with a Fuller tapered dril OF THE CORRECT SIZE. Lube the screw by dipping the tip of the screw in linseed oil.

If this proceedure was not followed, after a week, the screws cannot be removed from black locust without breaking.

Re: WC Weekend Accomplishments.....

#11

Re: Sunny Days

matt overton

Aren't Weimaraners the best?

Re: WC Weekend Accomplishments.....

#12

Jim in Burlington Ont.

You are so right Matt

Jim in River Oaks, Ont.

Hi Matt,

Jazz is our third Weim, all of them rescues.

It's hard to think of another type of pup I'd want, I love them all but Weims have found a place in my heart!


Take care,

Jim