Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

How did I live without a bandsaw?

Posts

How did I live without a bandsaw?

#1

How did I live without a bandsaw?

Stephen Kirk

I just picked up a Jet 14" Pro bandsaw. Nice tool. Went together easily, adjusting wasn't too bad. Even with the stock 3/8" blade it's cutting ok. 1 1/4 HP motor has decent power. I've got a 1/2" PS Wood blade to put on it. Dust collection is decent too. Doesn't come with a fence, but after market ones are better anyway.

I knew I needed and wanted a bandsaw, but it's amazing just how many things are easy on it. Clipping off corners, cutting short lengths of dowel, tenon shoulders. I have the feeling I'm going to hit the start button a lot. I never really knew what I was missing out on. And I haven't even done curves or resawing, which I originally got the saw for.

I can understand why many suggest a bandsaw as a first purchase. It has a lot of uses. Can't wait to see what else I can do with it.

Re: How did I live without a bandsaw?

#2

A.J. Hamler

Re: How did I live without a bandsaw?

A.J. Hamler

Due to space constraints, for many of my earlier shop years a 14" Makita band saw was my only stationary saw, and I discovered all the things you mentioned. While ideally a well-equipped shop would have both band saw and table saw, I wouldn't hesitate to recommend a band saw to somebody who could only choose one.

By the way, be careful when cutting dowels (or anything else round) on a band saw. Their cylindrical shape and the absolutely vertical downward travel of a band saw blade can combine in startling and unexpected ways. DAMHIKT.

Re: How did I live without a bandsaw?

#3

Re: How did I live without a bandsaw?

Stephen Kirk

I try to be careful with everything. Round things do have that tendency to spin, but the table saw can really chuck them. A little grooved board holds them fine, though.

I currently resaw on my table saw, which I've never felt particularly safe doing, so I'm looking forward to using the bandsaw.

Re: How did I live without a bandsaw?

#4

Re: How did I live without a bandsaw?

George Colonel"s Workshop-Havertown, PA

Good Morning Steve,

I felt the same enthusiasm when I got my first bandsaw, a Craftsman tilt top 12 incher, since replaced by two successive Jet 14"ers. I use it every day for those things you mentioned. The resaw feature has yielded lots of veneer from too thick stock, saving jointer and planer knife wear. I don't see how I could be without one.

George

Re: How did I live without a bandsaw?

#5

Re: How did I live without a bandsaw?

George Colonel"s Workshop-Havertown, PA

Steve,

The thin kerf from the bandsaw is goinjg to save you wood, and minimize dust.

George

Re: How did I live without a bandsaw?

#6

Re: How did I live without a bandsaw?

Dave Paine

If you are looking to re-saw, I would consider getting a Woodslicer blade from Highland Hardware.

You mention about having a 1/2in blade from PS Wood, who get them from Timbre Wolf. These are good blades. I normally use these blades, but I purchased a Woodslicer and it did work better in deep resawing.

Tuning the saw is very important for deep resawing.

Woodslicer recommends high tension. Timbre Wolf recommend low tension. Both can work.

If the saw is not tuned, you may look to be cutting on your line at the top of the wood, but then when you finished and look at the offcut and remainer, may find the bottom of the blade took a path of its own. DAMHIKT.

Check for the wheels to be co-planer. Check that the blade is running in the centre of the wheels. Check to have correct clearance on upper and lower guides. All can have an impact on re-sawing.

Mark Duginski has an excellant book on using Bandsaws. Highly recommended.

Re: How did I live without a bandsaw?

#7

Re: How did I live without a bandsaw?

Stephen Kirk

Thanks Dave. I know when I set up to resaw I will likely have some tuning to do. Bandsaws are great, but can be a little finicky. I was thinking of getting a Woodslicer and only pulling it out for heavy resaws. Luckily, I tend to work in smaller sizes, only 6-8", which isn't quite so intensive.

Re: How did I live without a bandsaw?

#8

Re: How did I live without a bandsaw?

FredD

For curve cutting you will need a 1/4" wide blade , preferably a 3-4 tooth skip tooth configuration .

The 1/2" blade you have will do a fine job on long sweeping curves, but not any with a tight radius.

FredD