Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Saw Tape

Posts

Saw Tape

#1

Saw Tape

Mark Mandell - Gone Round In Jersey

I need to replace the stick-on ruler on my table saw rail. When the saw is set dead nuts at 12", the 30" mark is off by more than a 16th.

Anyone here replaced theirs rule and , if so, whose did you use?

Thanks

Re: Saw Tape

#2

Dale Lenz

Re: Saw Tape

Dale Lenz

Replaced mine several years ago, think I purchased over the web(??). If you google: beismeyer fence measuring tape, there are plenty of sites. Good luck.

Re: Saw Tape

#3

Re: Saw Tape

George Koch

Mark, isn't the indicater mark adjustable on you saws fence?

Re: Saw Tape

#4

Re: Saw Tape

Mark Mandell - Gone Round In Jersey

Yes, George, it is. But if I take my 12" steel rule and set the blade-to-fence at precisely 12", adjust the indicator hairline to precisely the 12" mark, then slide the fence out and put the hairline on 30" my other steel rule tells me that it's actually set to 30-5/64. The is obviously an inherent error in the stick-on rail tape, so I want to replace the tape. Just want to do it with one that someone else has found to be accurate. Since I rarely rip anything wider than 12-18", I never noticed the error before.

Re: Saw Tape

#5

5/64 over 18" is a lot, but if you will....

Barry Irby

lower the temperature in your shop by 269.34 degrees fahrenheit it should be right on.

Re: Saw Tape

#6

Ps, You can thank me later.

Barry Irby

Re: Saw Tape

#7

Size Matters

Mark Mandell - Gone Round In Jersey

Sounds like a plan.

I'll let you know . . .

Re: Saw Tape

#8

Re: Saw Tape

George Koch

Sorry Mark, I misunderstood your your first post. On the rockler site they have yellow ones, and on the woodcraft site they have the white ones from a couple different suppliers, one of which was Kreg. George

Re: Saw Tape

#9

Re: Saw Tape

Mark Mandell - Gone Round In Jersey

Thanks, I'll check it out. Hopefully a name brand will be better that funk I have now. :)

Re: Saw Tape

#10

But then he'll have to wear a sweater in the shop

Bill Houghton, Sebastopol, CA

not being a Minnesotan and all.

Re: Saw Tape

#11

Moses Yoder

Re: Saw Tape

Moses Yoder

I imagine these tapes can stretch as they are applied. I would buy a good brand name like Kreg then clamp a steel rule to the rail and match up the inch marks as you apply the tape. I have a Biesmeyer fence and so far as I know the tape is accurate along it's full length, although reading your post makes me want to double check it.

Re: Saw Tape

#12

Re: Saw Tape

George Koch

The replacement tapes I've used were made of steel, so I guess it becomes a matter of which steel tape is correct, the one your installing or the one your checking it with.

Re: Saw Tape

#13

Reference Rule

Mark Mandell - Gone Round In Jersey

I have very good (but not Starrett) 12" and 30" steel rules that I use to reference most every other measuring tool against so that things are consistent. Every reel tape is checked against them, and any "error" (usually about a 64th) is marked "+/-" on the tape case and allowed for when in use.

When I get the new rail tape, that will be zero-set to the blade teeth, and then checked for consistency out to the end with the steel rule. If the graduations aren't smack on, it goes back for them to try again.

Re: Saw Tape

#14

Jason Roehl in Lafayette, IN

A couple questions...

Jason Roehl in Lafayette, IN

1. Do your 12" and 30" steel rules agree with one another? (I'm assuming they're not 5/64" off from each other, but you didn't address that issue, so it begged the question.)

2. If you mark "+/- 1/64" on a tape measure, is that a proportional error, or does it occur at a certain point? I.e., is 10" dead-on, then at 11" it's 1/64" error, or is it 1/64" error at 12" and 1/32" error at 24", etc.

Jason

Re: Saw Tape

#15

Re: A couple

Mark Mandell - Gone Round In Jersey

1. The two steel rules match as exactly as my eyes can tell. It is the tape glued to my table saw rail that is off by 5/64th. How, you ask, did I find the 5/64's extra with a 30" rule? With the fence sitting on the 30" mark, there was a gap when the 30" rule was set between the blade and the fence. I then measured that gap to find the difference.

2. The tape measures are checked with the 30" rule. Since I don't buy cheapo tapes, any discrepancy (usually a 64th) is consistent from the hook.

Hope this clears it up for you.