Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

Extending table saw top

Posts

Extending table saw top

#1

Extending table saw top

Lynn Reedy

Greetings from Soddy Daisy Tn.,

I have a powermatic contractor series table saw and I want to extend the top so as to handle large sheet of plywood more safely. I want to extend the top, after the wood is cut so we are talking about the

non-operator side of the saw. Due to limited storage I must be able to fold it down when not in use. My saws motor hangs on the back side of the saw and the top must fold up and down around it. I see a top with a large hole in it to make this happen. Any suggestions as to material and do's and don'ts.

Thanks for your help,

Lynn Reedy

Re: Extending table saw top

#2

Re: Extending table saw top

Herb Wofford

I believe, either Woodworkers Journal or American Woodworker, did and article on one that is on hinges and folds off the back of the saw. As to when this article was written, I am not sure, but I believe in the past couple of years. You may check their web site or e-mail the.

Hope this helps.

Herb

Re: Extending table saw top

#3

Re: Extending table saw top

Pat Evans

Do you have room for a portable storage unit, the top of which could double as your saw extension? Whatever the solution, MDF has a slick smooth finish to make pushing sheet goods easier.

We have good friends that live on Little Bend Road near you. Beautiful country!

Re: Extending table saw top

#4

Re: Extending table saw top

Barry Irby

I have another brand contractors saw. For mine I have a set of home made rollers mounted on a stand. They are slightly low on the saw side and high on the outfeed side to facilitate "picking up" the work. I also keep them slightly "twisted" or angled toward the fence so they help hold the work to the fence. These rollers have gotten common and cheap in the last few years. Perhaps that would work for you. (I made Mine out of and ancient tread mill I found)

I saw a solution for an out feed table for a contractors saw. As I recall the table was loosely attached or basically hanging on the far side of the saw and was some sort of sheet goods with a plastic laminate top. The sheet of MDF or whatever had a hole cut in it to allow the motor to tilt to a full 45. Maybe 2 or 2 1/2" in diameter. At that point there was nothing there except the laminate. You could actually have a hole in the top and it wouldn't matter for an out feed table. The whole thing could be lifted off and the legs folded up and hung on the wall, if it got in the way.

Another thought would be to build a storage cabinet, perhaps on wheels that was the correct height to serve as an out feed table. I recently mounted my planer on such a box, but made the top exactly the same height as my bandsaw table. So now my planer serves as an in fed or out feed for my bandsaw depending on where it is parked. A roll around table could be useful as and assembly table also. I also made one that has a grid for a top and is slowly becoming a downdraft sanding table. In a small shop everything needs to multitask and stay out of the way.

Re: Extending table saw top

#5

Re: Extending table saw top *LINK*

Dave Paine

What you refer to is an outfeed table.

Many results if you do an internet search for "Contractor saw outfeed table plans"'

The link below is one from Wood magazine. I forget which volume.

Lower in this page is a link "Bill of Materials and Fence Clearances Diagram" which is an excellent diagram and BOM details. The link is not obvious until you hover over with the mouse.

This uses a fixed shelf over the motor and then a foldable second portion


http://www.woodmagazine.com/woodworking-plans/tablesaw/must-have-rip-and-flip-tablesaw-outfeedtable/?page=1

Re: Extending table saw top

#6

Re: Extending table saw top

George Colonel's Workshop-Havertown PA

Good Morning Lynn,

I used Barry's method for years, successfully. Also used an auxiliary tool chest top for the same purpose. Recently I built a plywood outfeed table which I like best. Mine hinges at the rear of the saw, and are bolted to the rear rail. My outfeed table hangs to the floor when not deployed. Otherwise, it is kept in place by two diaginal braces on cleats attached to the underside of the outfeed table. It gives me lots of outfeed with little to limited shop[ space.

I realize you have a big motor hanging off the back of the saw. I'd built a short platform to cover it, perhaps anchoring it to the dolly, or bracing it to the saw legs. Frfom that platform, hinge your outfeed table so that it hangs straight down to the floor. When it is not in use, it will add only its thickness to the foot print dimensions of your saw.

Cutting a hole to accommodate the motor while hinging the table at the back of your saw may be effective, too. I'd worry about stock hanging up on the hole edges, so wouldn't employ that design.

George