Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Down Draft Table

Posts

Down Draft Table

#1

Down Draft Table

Ed Wesolek

Hello Everyone,

I have enjoyed reading about everyone and the different issues that they face and I feel very blessed and lucky in my life. I thank you for that alone.

I am in the process of building my benches for my work shop. My brothers came over and helped me build a 9' x 9' table for my table saw and it turned out very nice.

They are asking what is next so I am looking at making a down draft table for sanding. I have a 3 horse motor 220 for a vacuum system to use. My question is do I use the big vacuum system or some small squirrel cage to pull the sanding dust down then use the vacuum? I am checking on the power usage between the two to see if what the difference is.

I have recieved a lot of information from this group and feel very fortunate that I can be a part of it. I also know that I owe this group some picutes of what I have been building over the last couple of years and I will learn how to do that and give you a tour of what we ahve been doing.

Thanks for letting me a part of your life, I am very grateful for being a silent parner.

Re: Down Draft Table

#2

Re: Down Draft Table

Barry Irby

I have looked into these. I actually built one, sort of.

I got a HVAC guy to give me a couple of used furnace blowers. My reading indicated that they need huge airflow to be effective. It occurred to me that if I connected the table to the DC it would suck lots of air (heat or AC) out of the shop. My DC is outside in a closet.

I started out to make a table with one or two furnace fans. Lots of filters. The problem is that you need excellent filters to get the fines out of the air. Then you have to service the filters and remove the dust from the device.

I have a very small shop and really no room for anything new, so I ended up with a multi function roll around cart. It can be parked under the wing on my RAS. I can pull it out and use it as an assembly table. I can store scraps in the bottom (where the fans would have been). In the top there is a tray and the top is a grid. I cut a hole in the side and I insert the hose for the DC. So its an assembly table/storage/downdraft table. Doesn't work very well. A four inch hose does not provide enough air flow. It's better than nothing, but not a lot.

I think you need huge air flow. Also if you could put sides on it and maybe even a hood to confine dust and direct the airflow it would be better. I do like the fact that mine draws the dust into the DC outside the shop. Nothing new to service and no worries about the quality of the filters. If it catches a particle of dust its gone outside or in the DC and not blown through the filters back into the shop. It does rob heat because you leave it running for quite a while as you sand and sand and sand.

Re: Down Draft Table

#3

Re: Down Draft Table

Dan Donaldson

You want a squirrel cage or something like it to do the pulling of the dust. That application requires a lot of airflow, but not a lot of velocity. A vacuum has a lot of velocity so it can pick stuff up, but does not flow much volume. Exactly the opposite of what you need.

Re: Down Draft Table

#4

Re: Down Draft Table

Dave Paine

Are you hand sanding or using tools without dust extraction?

I do very little hand sanding and so clean up with shop vac afterwards.

Most of my sanding uses tools which have integrated dust extraction. These are connected to the shop vac during use. Almost no residual dust.

As the other replies state, a good downdraft table needs a lot of airflow.

I had a tour of Martin Guitar and they have some amazing dust collection at various sanding stations. All dust went down. Not cheap.

Re: Down Draft Table

#5

Re: Down Draft Table

Lee Schierer McKean, PA

We purchased a Grizzly downdraft table for some sanding work we do here at work. It has a small squirrel cage blower and uses hepa style furnace filters. I would think that a DC system would be able to do the same job. I don't think a shop vac would work well as the air cfm moved is too low.

Lee

Re: Down Draft Table

#6

Re: Down Draft Table

Ed Wesolek

Thank you for the replies. Right now I have an open space where I can build a down draft table. From the comments it sounds like I need a couple of squirrel cage fans with some ultra fine filters. Then right next to the table have a hose extensions to clean up after I have completed sanding.

Thank you for your input as that is what I am going to do.

Re: Down Draft Table

#7

Re: Down Draft Table

Phil Joines

The shop I worked at until the depression had about 20 DD tables. Most had 1/2HP impeller blowers and used 2" thick HEPA filters. Any area of the top that isn't being used needs to be covered to block the air flow.

Re: Down Draft Table

#8

Re: Down Draft Table

FredD

I have a Delta downdraft top that is easily carried to the top of a cart I put scrap in and it runs off of a 4 inch port connected to my Oneida DC.

Works well , but I seldom use it.

FredD