Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Chairs

Posts

Chairs

#1

Chairs

Tony - Memphis

Well, I finally go tthese chairs done. I actually finished them in November, but we just now got them covered. The upholstery guy delivered them Saturday. They did a great job. Covered up all my mistakes! The wood is makore and poplar. I used Lockwood dye stains. The finish is wipe on poly (Rockler I think). The design is based on lots of references (including Norm's chair). The arms are my own. They sit well and are pretty comfy. Easy to get in and out of. They are a probbaly a little low for most folks. Looks like a lot of these were that way though. I've heard we've grown in the last 200 years. My wife and I, however, have not! So they fit us well. I could have narowed them up a bit too, but they are still ok for us. They call these lolling chairs or Martha Washington chairs. I did the design in Sketchup. Anyway, these pics are a little fuzzy because they came from my phone...


Re: Chairs

#2

Re: Chairs

Jesse Cloud

Nice chairs. I really like the arms!

Do you have any 'work in progress' pictures? I'm curious about what's under the upholstery.

Re: Chairs

#3

They look comfy Tony

Thomas Skaggs, Foothills of Mount Level

Hey Tony....great job! A lovely pair of chairs. Nice proportions and they look like a very comfy sit. Well done sir!

Tom

Re: Chairs

#4

David Barnett

Re: Chairs

David Barnett

Very nice. Tasteful. Restful looking.

Re: Chairs

#5

Nice!

Bill Tindall

Just thinking about chair joinery makes my head hurt. When you spring for a camera show us the joinery.

Re: Chairs

#6

Re: Chairs

Tony - Memphis

Foam core and duct tape! Not really...

Lots of angles here. The backs tilt back around 14� and they taper out from the seat about 2� (subtle but effective). I drew the whole thing in Sketchup and used that to figure out a few things such as where the arms meet the back. I rough cut a lot of the joints on the TS with tenon jig or a homemade jig and then finished them by hand. The mortise and tenon where the arms meet the post was pretty difficult. I know that joint wil see some stress, so I was concerned about making it good and snug. Fun project, but now I am working on a "paint and putty" project to wind down!


Re: Chairs

#7

Re: Nice!

Tony - Memphis

Me too! I posted a couple of pics above. I used Sketchup to help with the angles. You may notice a digital protractor on my bench. That helped some too. Figuring out how to make the angels on the ts was a head scratcher.

Tony

Re: Chairs

#8

Re: Chairs

FredD

I always thought Chair making required a higher level of skill then nearly any other furniture project one commonly sees around the house and it looks to me that you definitely have that Skill set. Good Job.

FredD

Re: Chairs

#9

Alan Young

Bravo!

Alan Young

Thanks for posting all those pictures of you chairs-smooth, classy look.

Re: Chairs

#10

Re: Chairs

Joe in a Cleveland suburb

Very nice.

Well done.

Re: Chairs

#11

Any good sources on building upholstered furniture

Scott in Montana

I've done searches in the past for any media on building frames for upholstered furniture and came up with nothing. The only thing I've found have been one or two on New Yankee Workshop and a dozen different Morris chairs.

How about on couches, reading chairs, and such? I don't have to tell you what will happen if I start taking her couch apart to see how it is built...

Thanks in advance.

Scot in Montana

Re: Chairs

#12

Re: Any good sources on building upholstered furni

Tony - Memphis

Not really. I found a book by Singer that showed a bunch of frames and how to upholster them at a fabric shop. Jeff Greene's book has a couple of wingback chairs in it. I did some searching on the web for frames. There are companies that sell frames out there. I looked at furniture sites for dimensions. There are some chair books out there that give some basic dimensions. You have to consider the seat material and how much it will give. I actually went to furniture stores and measured and "felt up" the furniture to get dimensions and feel what was underneath. Some antique furniture books like Sack's have photos of furniture without the upholstery. Anyway, I just sort of used all that stuff and started drawing. I built a settee a few years ago and went through a similar exercise. Your upholsterer can give you pointers too. My settee design was 100% mine and I left off a couple of things the upholsterer would have liked. He suggested that I should have added more tilt to the back becuase when he covered it, a lot of that got covered up and the back is a little to straight up. Oh, and be prepared for sticker shock - upholstery is expensive! So is good fabric.

Tony

This is before I shaped the arms....


Re: Chairs

#13

Re: Any good sources on building upholstered furni

FredD

Regarding your frame picture Tony, I occasionally repair frames or make new parts for a buddy of mine that is a upholsterer and I must say the material used and the workmanship by Furniture companies pales in comparison to what you did.

Many of the cheaper couches and Chairs have what looks like rejected pallet material for wood pieces.

FredD

Re: Chairs

#14

Outstanding !

Don Orr

Re: Chairs

#15

Re: Chairs

gary peterson

great looking chairs, one thing I would like to do is be able to upholster.

Re: Chairs

#16

Ellis Walentine

Very nice, Tony

Ellis Walentine

I enjoyed your recounting of the process. The finished result is lovely, and hopefully as comfy as it looks. Thanks for posting. The upholstered form is one of the most neglected by woodworkers.

Cheers,

Ellis

Re: Chairs

#17

Re: Any good sources on building upholstered furni

Keith Mealy

Don't know if this helps, but there is a company that makes frames.

http://www.chervan.com/

And I agree, most contemporary frames are "engineered wood" (particle board, wafer board, plywood, etc.) that is stapled together.