Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Help Help - softening or dissolving rubber

Posts

Help Help - softening or dissolving rubber

#1

Help Help - softening or dissolving rubber

Terry Alexander

Why do we get into projects for in-laws?

BIL had another "project" for me. Wants me to rebuild an air rifle. Ok....this pellet gun is old old old. It will pump up to a gazillion pounds of pressure. However, the seals (inside) need replacing. And....yep....there are companies out there that specialize in parts for these old pellet guns.

Step 1 is dis-assembly. BTW....did I mention that I used to do some amateur gun-smithing? However....not pellet guns.

Dis-assembly...no problem.

Inocuous statement in the rebuild kit: "Remove the old rubber gasket". This gasket kind of pressure fits into a metal surrounding. It has been in there so many years it is as hard as steel. I swear I could finish this rebuild in about 15 minutes if I can get out this rubber gasket. I have tried a utility knife (whew....close to needing stitches).

Having said/typed all of that. Do any of you chemistry majors (or whatever) know what I can soak the gasket part in to get it soft enough to remove? It is in a steel casing, so I not opposed to using something caustic.

As always......thanks in advance!

Terry Alexander in West Texas

Re: Help Help - softening or dissolving rubber

#2

I don't know but you might try....

Bill Tindall

Who knows what the polymer is in the seal. It could be rubber but probably isn't.

Depending on what you have on hand try- cold or hot diesel fuel, lacquer solvent, xylene.

Re: Help Help - softening or dissolving rubber

#3

Clint Searl

Gasoline

Clint Searl

Re: Help Help - softening or dissolving rubber

#4

Re: Help Help - softening or dissolving rubber

Ron in Sterling, CT

In the early days of seals/sealing many of them were made out of neoprene, which swells and softens in petro products. I agree with Bill on the Diesel fuel, or kerosene, to soak them in. Good Luck.

Ron

Re: Help Help - softening or dissolving rubber

#5

Re: Help Help - softening or dissolving rubber

Dan Donaldson

In a previous incarnation, I had to remove rubber insulation from connectors and relays for rebuilding. We used dichloromethane to soften it for removal. You can get it in a hardware store as paint stripper (zip strip for one brand). Nasty stuff, use in well ventilated area and with gloves. Might be something to try if all else fails.

Re: Help Help - softening or dissolving rubber

#6

Re: Help Help - softening or dissolving rubber

Jim Dillon

Terry,

If the gasket is indeed latex rubber (unvulcanized), then soaking the gasket in oil or grease for a few days might soften it enough to easily pry/cut it off. If it is vulcanized, then your options are limited to brute force :D . As another poster said, neoprene is often a substitute gasket material. In this case, ketones (acetone, methylethylketone), esters (ethylacetate), or chlorinated aromatics (o-dichlorobenzene) might work, but availability varies. N-vinylpyrrolidone (a lactam) is sometimes a good polymer solvent and is the principal ingredient in one brand of paint stripper. A related class of aprotic solvents include DMF (dimethyformamide), and DMSO (dimethylsulfoxide) which might soften the neoprene material. While I've used all these solvents in my previous life working with polymers, most of the mentioned solvents are not readily available to the general public.

Jim

Re: Help Help - softening or dissolving rubber

#7

Biodiesel

Lee Schierer McKean, PA

Get some B-100 biodiesel AKA 100% biodiesel. It will dissolve/soften most rubbers.

Lee

Re: Help Help - softening or dissolving rubber

#8

Have you tried soaking in lacquer thinner?

Gary Smyth

Re: Help Help - softening or dissolving rubber

#9

Heat gun?

Grant in Iowa

I realize torch type heat would likely be too much, but you might consider trying heat from a heat gun to soften the gasket material. Perhaps holding it in boiling water might be an option, too.

Another thing to consider is alcohol. It is known to destroy all but modern rubber compounds.

FWIW,

Grant in Iowa

Re: Help Help - softening or dissolving rubber

#10

One of the first things...

Dale Lenz

I'd try would be EZ-OFF oven cleaner in the yellow can. Test that it will not harm the metal. Might take 2-3 tries.