Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

PM 63A alignment Follow Up ?

Posts

PM 63A alignment Follow Up ?

#1

PM 63A alignment Follow Up ?

Rick Lasita

I managed to get the blade back into alignment, thanks for all the advise yesterday. I have another question regarding the wiring of the on/off switch. Since my saw is on a mobile base with drawers etc, I unbolted it and leaned it forward to get to the trunion bolts and I guess when I removed the motor, it pulled the black and white wires off on one side only.

Looking at the back of the switch the blk/wht wires on the left are off (GRN stayed on) wires on the right are still attached

? O O GRN

? O O BLK

GRN O O WHT

Load Line

I can't remember how I had it when I installed the safety paddle switch. Thanks for the help. Rick

Re: PM 63A alignment Follow Up ?

#2

Re: PM 63A alignment Follow Up ?

Bill Houghton, Sebastopol, CA

I don't quite grasp the layout you were trying to convey.

If you've got a volt-ohmmeter (also known as multitester), check which terminal on the load side (the side going toward the motor) relates to which incoming wire, and match the colors - white to white, black to black. If you don't have a multitester, the terminals opposite each other on the sides of the switch are probably what gets turned off/on as you operate the switch.

Re: PM 63A alignment Follow Up ?

#3

try this

Bruce, a MN Galoot

from the powermatic site:

"A: For technical service concerning JET, POWERMATIC, PERFORMAX, and WILTON retail products please call 800-274-6846 - 7:30 a.m. to 5:30 p.m. (CST, Monday - Friday)."

Re: PM 63A alignment Follow Up ?

#4

Re: PM 63A alignment Follow Up ?

Rick Lasita

Bill, thanks, I don't have a meter, so if I understand your answer, looking at my diagram, I attach the balck across for the black, white, across from the white ? Rick

Re: PM 63A alignment Follow Up ?

#5

Re: try this

Rick Lasita

Thanks Bruce, I tried that before writing to the forum, the person I spoke with didn't have a clue as this is a safety paddle switch that replaced the original switch supplied with the saw back in 89.

Re: PM 63A alignment Follow Up ?

#6

Moses Yoder

Re: PM 63A alignment Follow Up ?

Moses Yoder

I multimeter is one of the better investments in a woodshop, especially if you plan on wiring this yourself. If it's an aftermarket switch you might need one to figure out where the wires go. An electrician could fix it to, probably for a $90 service charge. A multimeter runs prolly around $20 for a cheap one and then a couple hours to figure it out. If you are not handy around electricity, call the professional.

Re: PM 63A alignment Follow Up ?

#7

A variation, then

Bill Houghton, Sebastopol, CA

Is there a maker name on the switch itself? If so, Googling the maker name might bring you a phone number to call.

Re: PM 63A alignment Follow Up ?

#8

Re: PM 63A alignment Follow Up ?

Rick Lasita

Thanks Moses - I will pick one up for future needs. Didn't realize this was a tough question, maybe I didn't explain it very well. I have all but 2 wires on the switch, there is one black, and one white loose. Do I attach the black wire across from the other black, and the same for white? I think that is all I need to understand to get the saw running this afternoon. Appreciate the responses.

Re: PM 63A alignment Follow Up ?

#9

Re: PM 63A alignment Follow Up ?

Chuck Lenz

If I'm reading you correctly, there were four wires attached to the switch. To me it would indicated that your saw is wired for 220V. I would also tend to think that 2 blacks should be on one side of the switch, and the two white wires should be on the other side of the switch, as in the hot wires black and white should be at the top two oposite side lugs, the wires black and white going to the motor should be at the bottom two oposite side lugs. I'm no electrician, so don't go by what I say, wait for others to respond and either confirm what I said, or discredit me.

Re: PM 63A alignment Follow Up ?

#10

Re: Something to consider

Chuck Lenz

On the Delta Contractor's saw that I own there is a quick disconnect about 6 inches out from the motor. You may want to consider doing that to yours also so the next time that you want to remove the motor you don't have to go through what your going through now.

Re: PM 63A alignment Follow Up ?

#11

Re: PM 63A alignment Follow Up ?

Rick Lasita

Thanks Chuck, I should have added it is 110v and there is one black and one white that didn't come off on the load side of the switch

Re: PM 63A alignment Follow Up ?

#12

Re: PM 63A alignment Follow Up ?

Rick Lasita

meant to say the LINE side of the switch that till has the wires attached that did not come off

Re: PM 63A alignment Follow Up ?

#13

Re: PM 63A alignment Follow Up ?

Barry Irby

Rick, I'm sure you have realized by now that this is a great use for a digital camera. Take a picture before you disassemble something. I wish I had paid attention to this notion before I started working on my car recently.

I would bet if you have a switch wired with a whale and black on one side, the other black and white wires go across form them. This would make sense compared to a switch I installed on my Performax.

Of course I am willing to make this bet because its your saw, not mine. Also pretty sure that if you hook it up and its wrong it will trim the breaker and not really harm anything. That's bad advice. You really should get eh meter and check it out. You could also check it out with a light bulb in a socket with wires hanging out. Just go from ground to the line black and the bulb should light. Then go from ground to load black. Switch on, bulb lights, switch off, bulb does not light. Then with the switch off go from line black to load white and bulb does not light. Switch "on" bulb does light. You could wire short leads to the plug on any light and use that. If you do this be careful and tape up the connections to keep from getting shocked. I usually have enough junk parts laying around to make a home made continuity tester.

Re: PM 63A alignment Follow Up ?

#14

Re: PM 63A alignment Follow Up Problem Solved

Rick Lasita

Barry, you are right, a camera, or at least a diagram (which I now have both) would have prevented a lot of grief. Good news is the problem is solved, the answer was black on the load to black on the lead,- white/load, white/lead, checked with a meter. Runs fine, no smoke :) and the alignment works as well. Guess this will hold for a while. Thanks again for the help. from everyone.

Re: PM 63A alignment Follow Up ?

#15

Re: PM 63A alignment Follow Up ?

Keith Newton----Little Rock, Arkansas

If you know that they both are either coming in together, or going out together, it should not matter in a 4 pole switch for AC current. But if the black is on the top of one side, then I would do the same on the other.

Re: PM 63A alignment Follow Up ?

#16

Re: PM 63A alignment Follow Up Problem Solved

Barry Irby

I think you have a Double pole single throw switch. DPST. If true, that might indicate you could covert the motor to 240 fairly easily and would not have to rewire the switch. At the moment you have a switched neutral.

Re: PM 63A alignment Follow Up ?

#17

Re: PM 63A alignment Follow Up ?

Chuck Lenz

Rick, I guess that even if it's setup for 110V, I would think that blacks on one side of the switch, then whites on the other side. Another way to confirm it would be like on an outlet, black to the gold colored screws, and whites to the silver colored screws. As I stated before though, I'm not an electrician, but I did stay at a Holiday Inn once. Can you get us a picture of the switch and whats going on ?

Re: PM 63A alignment Follow Up ?

#18

Nothing wrong with a switched neutral, though...

Bill Houghton, Sebastopol, CA

is there? As long as the hot leg is switched too.

Re: PM 63A alignment Follow Up ?

#19

Not as far as I know.

Barry Irby