Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Table height

Posts

Table height

#1

Table height

Doug Ridley

I have been asked by our church to build a table to fit a certain space. It will have two drawers in front and will be used for a laptop. The size for the space is no problem. I need to know what the optimum height needs to be from the floor to the bottom of the drawers so she can get her knees under it and what optimum height from floor to top of table so she can comfortably use the laptop. I figure about 6 to 7 inches from the bottom of the drawers to the table top. Suggestions please.

Doug

Re: Table height

#2

Re: Table height

Keith Newton----Little Rock, Arkansas

Doug, I like to use 29" for the top height, and 25" for leg clearance.

But as you can see, there is no way to achieve both of those using a deep drawer as you propose.

Re: Table height

#3

slight difference of opinion

Bill Tindall

30" and 25" are common dimensions for desks, which results in a 3" drawer. If you need bigger drawers then a stack of drawers to the side will be required. For me personally, a 29" height would be fine, but my chair will need 25" to slide under.

Best would be to sit the person of interest in their preferred chair and measure. Depending, one might lower either dimension about an inch, or raise for an exceptionally tall or large person.

Re: Table height

#4

Ellis Walentine

"Secretarial" height

Ellis Walentine

No, it has nothing to do with horse racing. Secretarial height, in the contract furniture world, is 26", give or take. This standard was devised when secretaries still used typrwriters, and the height was designed to put the typewriter keys at a comfortable height relative to the secretary's upper body. Specifically, you want the forearm to be approximately level when the fingers are on the keys. Laptop keyboards are an inch or two closer to the table surface than typewriter keyboards, so you could cheat the height upward by that amount. I would agree with Keith's suggestion of 25" for the knee clearance under the apron rail.

Ellis

Re: Table height

#5

Re: Table height

Doug Reynolds in Seattle

I am in the camp that does not think you can have the drawers under the table. Ellis mentions ergonomics which is really almost putting the keyboard in ones' lap and that leaves no room for drawers directly underneath. Speaking with our Safety and Claims/Disability folks just now, they said the forearms should be parallel to the ground or angled slightly downward when fingers are on the keys. Feet must be flat on the floor, back against the chair back. At six feet tall, my chair is all the way up, maybe four inches between the table top without drawers and my forearms are angled up slightly instead of down. So, that leaves me no room for any drawer regardless of height. My wife and I've had carpal tunnel surgery on both hands and sure would not want to build something that would cause someone the same fate.

Re: Table height

#6

Re: Table height

Doug Ridley

Good answers all. Thanks.

How 'bout this? 25" at front, 6" apron on one end and the back with a 6" drawer on the other end. Then I put a one inch apron in front with two angled braces at each front corner leaving a 25" high knee hole. As you can see I'm not very good at this so all help is really appreciated.

Re: Table height

#7

Re: Table height

AZ in Colorado Springs

I'd suggest you get some large card board boxes that you can cut up to make a full scale mock up. If you can get the lady in her chair, as one person suggested, you can trim away the card board over her knees to get the right size. It doesn't require a lot of detail, just the left and right sides of the front opening and a little bit of a top to rest the hands (and maybe a keyboard) on. Once you have those dimensions, you can fill in the other parts and pieces and deduce their dimensions.

Re: Table height

#8

Ellis Walentine

Negatory on the apron idea

Ellis Walentine

Doug, I wouldn't suggest that sort of apron arrangement for structural reasons. You want as deep an apron as possible for stability of the legs, and you want it on four sides. If you make the table at 28" - 29", you can probably get away with a 3 1/2" - 4" apron without banging anyone's knees. That's enough room for a deep pencil drawer.

Ellis

Re: Table height

#9

Re: Table height

Barry Irby

My cousin uses a laptop for here work. She has a separate keyboard mounted on an under table pullout/drawer and has a separate screen she plugs into the laptop. The laptop just lays on the desk, closed and plugged into the power supply. She uses the keyboard and screen unless she takes the laptop with her.

I would suggest you suggest a separate keyboard in a tray below the table top, flanked by drawers. Keyboards are cheap, screens, not so much. You could continue to use the screen on the LT.

Re: Table height

#10

Re: Table height

Doug Ridley

Somebody tell me what you think of this