Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

High speed grinder - narrow wheel

Posts

High speed grinder - narrow wheel

#1

High speed grinder - narrow wheel

Bill Houghton, Sebastopol, CA

I'm installing a wire brush wheel on my Baldor 3450 rpm grinder. Unfortunately, Baldor designed these for 1" wide wheels, and the spindle runs out of thread 1/4" before it touches the wheel flange (the big shaped washer that clamps against the grinding wheel). Can I just stack regular flat (cut) washers on the spindle as spacers, or do I need some kind of special spacer from the bearing house?

Re: High speed grinder - narrow wheel

#2

JL

Re: High speed grinder - narrow wheel

JL

Regular washers will work on the outside of the wheel. If you put them on the inside, make sure the washers have been trued and are REALLY flat (DAMHIKT).

Re: High speed grinder - narrow wheel

#3

Re: High speed grinder - narrow wheel

Virgil Johnson

The wire wheel is going to be a bit more forgiving when using washers as shims to take up the space. I would be sure to find washers with as little radial clearance as possible. Fender washers come to mind. if you have a piece of 1/4 aluminum (brass) a drill press, band saw and a belt sander (or are patient with a file) you could make your own spacer.

Re: High speed grinder - narrow wheel

#4

Should work...

John in NM

I've done that too, in addition to using a thicker spacer. As JL said, take a look at the washers to make sure they aren't visually out of round or the hole off center.

Be very careful with a wire wheel on a grinder, they can really grab parts from you and fling them across the room (I forgot all about this on the latest Ides of January thread :D).

Also, don't wear gloves. Though it may be preferable to protect your skin from the wire wheel, if you do brush a finger on the wheel you'll pull back quickly, where as with a glove you won't notice. The glove gets pulled in fast like the parts I mentioned - it's astounding how fast. I don't know what OSHA's take on the subject is, but this was the instruction I got from an employer who'd seen lots of accidents and it makes good sense to me.

Re: High speed grinder - narrow wheel

#5

Re: High speed grinder - narrow wheel

del schisler

the way i use mine is with washers. And i felive the center of the wire wheel has a plastic piece in the hole. and not metal. I leve mine a little loose so if i push real hard the wheele will slip. So it will not grab and tair off your hand. It still spin's enough to polish the item . just my 2 cents

Re: High speed grinder - narrow wheel

#6

Wear Eye Protection....Be sure the

Barry Irby

wheel is rated for the speed. I am sure washers will work, but if it were to throw a wire it could easily take out an eye.

Re: High speed grinder - narrow wheel

#7

Re: High speed grinder - narrow wheel *LINK*

Galen Vetterick

I purchased standard precision flat washers from my local ACE hardware for my applications. Not sure what store is close to you but you might give them a call to see if they carry them in your area. A little more money but sure run more balanced and my use is only 1725 rpm and lower.

Link is just for reference to sizes typically made. I used 1/2" bolt size.

If I mount a wire wheel I make sure I remove the tool rest to get it clear out of the way.


http://mortonmachine.thomasnet.com/viewitems/workholding-components-washers/standard-precision-flat-washers?

Re: High speed grinder - narrow wheel

#8

I sometimes put a narrow wheel on my TS

Keith Newton----Little Rock, Arkansas

If you are just wanting to use the narrow wheel to grind a shaper knife, I like to put it on my little contractor saw, and use the Koolmist sprayer to grind a lot of metal fast, while not overheating.

Otherwise, you could make a good washer from MDF or something like that.

Re: High speed grinder - narrow wheel

#9

Re: High speed grinder - narrow wheel

JIM SMITH

Hello, Please DO NOT EVER REMOVE a tool rest on a grinder, it gives the wheel a place to grab anything close to it and pull it into the grinder. Jim

Re: High speed grinder - narrow wheel

#10

Re: High speed grinder - narrow wheel *LINK*

Galen Vetterick

Jim

You might be interested in this one interpretation.

I also worked in a foundry and they never had tool rest on the wire wheel grinders and never were required by OSHA.

When I worked for a steel fab shop they too never were required to put tool rests on wire wheels.

Side and rear guards yes.


http://search.yahoo.com/r/_ylt=A0oG7k3yEkNN6AsAuapXNyoA;_ylu=X3oDMTE2NXNwcmkzBHNlYwNzcgRwb3MDMTAEY29sbwNhYzIEdnRpZANTTUUwMTNfMTUz/SIG=128e5leg1/EXP=1296270194/**http%3a//www.osha.oregon.gov/interps/1994/im-94-25.pdf

Re: High speed grinder - narrow wheel

#11

Re: High speed grinder - narrow wheel

JIM SMITH

Hello, I will still stand by my statement rather than something written by a person in an office who doesn't even know what he wrote about, with fifty years of using tools of every kind made, and forty three of those years in a large paper mill with 500 millrights, pipefitters,welders, machinist, and mechanics working on huge machines, I've seen what happens to hands and fingers when no tool rest were used. We had better not get caught anywhere near a machine without a tool rest in place. I'm proud to say I still have all ten of my fingers in place where they belong, even if I can only type with two of them!!!

Re: High speed grinder - narrow wheel

#12

craigd

Re: High speed grinder - narrow wheel

craigd

I made a big washer from aluminum plate for my Baldor. I have a knotted wire wheel mounted now and it is wide enough that a hardware store washer is all that is needed (along with the big belled washers that came with the grinder).

Re: High speed grinder - narrow wheel

#13

Re: High speed grinder - narrow wheel

james runchey

When the old 1"wheel on my Baldor wore out, I got a new !" from mcMaster Carr. Can't remember the cost though.