Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Zissner' Seal Coat Brush marks

Posts

Zissner' Seal Coat Brush marks

#1

Zissner' Seal Coat Brush marks

Bill Lordan, Auburn NH

I am in the process of refinishing a shuffleboard table. We have the old finish sanded off and I am trying to lay down a couple of coats of Seal Coat dewaxed shellac but I am continually getting excessive brush marks. I am using a guality bristle brush and have tried to avoid over brushing. Does anyone have any ideas what I am doing wrong - this is my third time coating and having to sand off the seal coat. I am seriously considering giving up on it but I had the club buy a gallon of it because I said it was so wonderful. FYI, I will be using Minwax Polyacrylic WB for a topcoat. I know there are better finishes but the club has an account with the local Ace and they prefer to get it there.

I would appreciate your thoughts on this.

Bill Lordan

Auburn NH

Re: Zissner' Seal Coat Brush marks

#2

Re: Zissner' Seal Coat Brush marks

Steve Schoene

Wrong brush. China bristle is way to coarse for best results without wonderful technique. There are three ways (at least) to go.

First is a artists watercolor wash brush with Taklon gold or similar very fine synthetic bristles. With a low reservoir, such brushes lay down a thin film with no brush marks. Alternatively a mop type brush with very fine bristles holds more shellac but can still laydown a brush mark free coating.

In either case the technique is fast. You only brush ONCE, except for an inch at touchdown where you land a bit short of the wet edge, move toward it, and then reverse to apply the shellac to the new area. If you miss a spot leave it for the next coat. Same with overlaps, though avoid as possible.

Third, and easiest for many, is to pad on the shellac. A pad of absorbant material covered with fine cotton percale can be used to apply shellac. You still need to move quickly and never go back over an area until it has dried. If you feel any drag with the pad STOP let the film dry some more before returning to it. (Allow no drag with brushes either.)

Re: Zissner' Seal Coat Brush marks

#3

Another Taklon technique, and , why shellac?

Bill Tindall

I attended a demonstration by Don William, Smithsonian conservator, on the topic of shellac. At the time I had never had a favorable shellac brushing experience (when the going gets tough, spray). For the brushing part of the demo he used a small Taklon brush and 1 pound shellac, a three fold dilution of commercial stuff. His brushing technique was to dip and brush like mad with overlapping strokes- think windshield wiper on high. Took seconds to cover the test panel. The material dried fast and he was able to recoat in minutes. It took several coats to get a good build.

I attended a similar class by a local furniture restorer. He used a large fine bristled brush, but similarly used 1 pound shellac, and quick, full-length slightly overlapping strokes.

My third demo was by Finck, the plane person. He padded, again using `about a 1 pound cut. Note this 1 pound cut keeps popping up.

But to back up, why is shellac being used at all?

Re: Zissner' Seal Coat Brush marks

#4

Re: Another Taklon technique, and , why shellac?

Bill Lordan, Auburn NH

The main reason I am using shellac is that I need to paint lines and use a decal of the club logo on the table. I had hoped to put down a coat or two of shellac, paint the lines, put down another coat of shellac to seal these lines, then a few coats of polyacrylic and then the slide decals followed by several more coats of the poly acrylic to bury the decals. If there is an easier way to accomplish this, I am all ears.

Thanks for any help you may be able to offer.

Bill Lordan

Re: Zissner' Seal Coat Brush marks

#5

Re: Another Taklon technique, and , why shellac?

Howard Acheson

The main reason I am using shellac is that I need to paint lines and use a decal of the club logo on the table. I had hoped to put down a coat or two of shellac, paint the lines, put down another coat of shellac to seal these lines, then a few coats of polyacrylic and then the slide decals followed by several more coats of the poly acrylic to bury the decals.

What paint are you going to use to paint the lines? Is there any reason that you can't just put a couple of coats of your final finish down, let it dry and then paint on top of that? The waterborne will provide a nice surface for almost any paint you decide to use.

Another point is that applying shellac with a brush is something that it takes lots of practice to master. It's particular problem on a large, flat surfaces. I would never recommend brushing shellac on something like a shuffleboard table. For large surfaces, spraying shellac is the best option. If you don't have spray equipment, buy a few cans of Zinsser Spray Can shellac. It's a totally dewaxed shellac and you might be able to end up with a better surface.

Re: Zissner' Seal Coat Brush marks

#6

Re: Zissner' Seal Coat Brush marks

Dave Bair, Eaton Rapids, MI

When I made my kitchen cabinets, I used SealCoat on all the interior surfaces. To be most efficient, I wanted to coat entire 4x8 sheets of plywood. After a lot of experimentation, and lots of brushing failures, I learned to use a white foam roller to apply the shellac, followed immediately with a light pass with a wide, flagged nylon brush to remove any bubbles created by the foam roller. (Black foam rollers dissolved from the alcohol.) Spray cans of Sealcoat often went on too thickly and filled the air with particulates and propellants, making it unusable in my shop.

Re: Zissner' Seal Coat Brush marks

#7

Re: Zissner' Seal Coat Brush marks

Bill Lordan, Auburn NH

Gentlemen;

Thanks for your responses. I think I am going to give up on the shellac and do as Howard suggest: lay down several topcoats and then paint the lines and install the decals. I will then continue with several more coats of the minwax polyacrylic to bury the lines and decals. Then I will wax. Any thoughts on the wax to use?

Re: Zissner' Seal Coat Brush marks

#8

question?

Bill Tindall

Why would you "lay down several coats" before adding the painting? Why wouldn't one or at most two do? I only put three coats of varnish on a new floor. It seems to me that one of two coats under and at most two over would be sufficient and minimize potential drying and checking problems of thick coatings.

You should test what ever scheme you intend to use on a test piece. Especially test adhesion to paint to what ever goes on top of it.

Re: Zissner' Seal Coat Brush marks

#9

Excellent Questions

Howard Acheson

I agree with your comments. Particularly the testing point. In addition to seeing the reaction of the paint being used, decals can be problematic under some finishes. The only way to know is to test the process completely on scrap before committing to the real project.

Re: Zissner' Seal Coat Brush marks

#10

I find shellac is easy

wilbur

Coincidentally, I used shellac for the first time this weekend, and I found it very easy to use. Actually, I made my finish from seedlac, a less refined version of shellac that still contains the natural wax.

I dissolved the seedlac in 190 proof Everclear to make a one pound cut, which seems to match the theme that Bill described above, strained the solution through some cheesecloth, dipped a rolled up piece of old T-shirt material in the strained seedlac, and padded it onto my project. It dried so quickly that I was able to get 5 coats on in 15 minutes, and the resulting finish was perfect. A little extra paste wax rubbed in, and I was done.

Re: Zissner' Seal Coat Brush marks

#11

Clint Searl

What a waste of Everclear!

Clint Searl

>:\ :\

Re: Zissner' Seal Coat Brush marks

#12

Re: What a waste of Everclear!

wilbur

There's a really good reason that to use Everclear instead of the denatured alcohol that you can get at the borg. The DNA at the borg by my house is about 50% ethanol, and 50% methanol, according to the MSDS. Methanol is highly toxic, and I really didn't want that stuff in my house. Shellac will dissolve more easily the higher the ethanol content, and the methanol slows down the drying.

The total cost for the shellac and Everclear works out to be about $25 a quart. Not bad compared to the cost of other finishes out there. By using the DNA from the borg I would have saved about $14, which I was fine spending if it meant that I didn't have to deal with methanol.