Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

blew hole in drawer front

Posts

blew hole in drawer front

#1

blew hole in drawer front

GolfSteve in Calgary

Any suggestions for how to fix this mistake? When trimming the lip of the half-blind dovetails for the drawer front, the grain was running the wrong way and I blew a hole through to the front of the drawer front. I super-glued the piece back in, but the repaired area is too thin and I need to do something to fix the problem...eg. an inlay, or fill the thing with epoxy and sawdust. I think a patch will be too visible on the drawer front and I hate the idea of making a new front since I don't have any matching wood left over.

Any ideas for the fix?

Picture from the front:


Picture from the back showing how badly the grain tore out when chiselling the final millimeter of wood to the line (I removed most of the waste with a trim router, so didn't realize the problem until I wacked the chisel to remove the waste to the line). The white spot is the repaired area where the superglue accelerator was sprayed.


Also any ideas for knobs/pulls? I have some cocobolo and/or ebony that I think would make nice pulls but don't have any good ideas yet.

Re: blew hole in drawer front

#2

Re: blew hole in drawer front

Henry (Raleigh, NC)

It would alter the look significantly, but you might consider adding a frame to make the drawer a Frame and panel front. Not sure how I would accomplish that given the stage of completion of the drawer but it was my first thought when I saw the whole piece.

Henry

Re: blew hole in drawer front

#3

Dale Lenz

Re: blew hole in drawer front

Dale Lenz

My thoughts are to fill the problem area with some blacken epoxy, this will leave this spot as a �natural� character mark.

Good luck,

Dale

Re: blew hole in drawer front

#4

Alan Young

Re: blew hole in drawer front

Alan Young

I like Henry's idea of adding a frame to the drawer front. Just gluing on a 5/8 or 3/4 by 1/8 thick frame that covers the hole might go well with the Doors which are already frame and panel. If that causes the drawer to move front of flush with the main cabinet framework you'd have to trim back the drawer sides by the thickness of the glued on frame/border.

-Alan

Re: blew hole in drawer front

#5

Re: blew hole in drawer front

Keith Newton----Little Rock, Arkansas

First, I think the CA was a good choice for the first attempted repair, but I'm not sure exactly how you approached it. If there were parts that came off, and you were able to put them back, that is good.

If there were tight cracks, you can get the CA to fill those, but as they get larger, I like to wet out the wood, then have a pinch of sanding dust from my belt sander bag, then smash it into the wet cracks, before saturating any dry area.

If that boiled white patch is showing on the face, and showing up bad after you glue the sides on, I like to handle repairs like this by cutting a little wedge shaped patch, about 1/8" thick or whatever the thickness of that front is. If you can cut the patch part where the little undulations pretty closely match the surrounding wood, you should be able to glue it on where nobody will notice.

With a wedge shaped part near the edge, you can get it really tight by driving it in from the side, then trimming off the excess after the glue dries. Since there is a lot of figure in that front, that should help to hide the repair.

Even if it can be detected, don't wig over it too much. Everybody makes mistakes, and a well handled repair doesn't hurt the overall finished results, it just shows another level of craftsmanship.

Now, As for gluing "Sawdust" into a repair, I wish there was a scrub button that could be hit, so that suggestion would never show up on woodworking sites again ever. Particle board is what you get when you glue sawdust particles together. Would you think you could get a good match by gluing a PB plug into a defect?

Re: blew hole in drawer front

#6

I concur

Lee Schierer McKean, PA

There are already some black pitch pockets showing on the front. I would try to glue in the pieces that broke out or with pieces removed from the dovetail areas with black epoxy. If the pieces are irregular in shape, the resulting glue line might appear to be just another black pitch pocket.

Lee

Re: blew hole in drawer front

#7

Re: blew hole in drawer front

paul in AZ

Several variables in this equation.

If you have some figured scrap around that matches the grain I'd first go with keith's idea of chiseling out that area and putting in either a triangular or irregularly shaped Dutchman. Tightly fitted in figured wood these are hard to spot.

From a design point of view a faux face frame would carry the lower door elements up to the drawer. That would simply mean recessing the drawer a bit deeper to get the flush front. Depends of course on if you have enough of the face frame wood left to slice some thickish veneer and if you like that look.

Gad, your dovetail work that nobody will ever see is WAY neater than anything I can do. Nice.

Re: blew hole in drawer front

#8

we need a better picture

Bill Tindall

I think I understand what caused the problem but it will take a close up of the problem to best determine how to fix it. I think a "frame" wide enough to cover it up will look too wide. The wild grain will be easier to fix, what ever the fix, so that is in your favor.

In general if there is a lot of wood missing then adding wood to match is the best way to proceed. But if most of the wood is in place and there are just a few vacancies then filling with "filler" is preferred.

As far as cyanoacrylate plus sawdust, the result is not particle board. The result is solid and non-porous and it can be an effective patch. My turning friends do it all the time with good results. Personally, I use shellac sticks.

Re: blew hole in drawer front

#9

Re: blew hole in drawer front

David Hay Denver

One idea that comes to mind is to cover up the hole with some inlay. Perhaps some stringing inlaid in a rectangle, inset from the edges of the drawer front?

David

Re: blew hole in drawer front

#10

Re: blew hole in drawer front

Joe Mohnike

Have you considered routing out the damaged area and glueing a matching piece. Being close to the edge you should not have any problems. I have done this in the past, and it has worked out well. I try and terminate the cut in a grain area that will hide the cut.

Good Luck

Joe M.

Re: blew hole in drawer front

#11

Better picture

GolfSteve in Calgary

Unfortunately I did not clean up the face after gluing the chunk that blew out back in. Once the bubbly glue is removed it will look like a fairly clean repair. There are small gaps around the circumference of the piece glued back on. The main problem in my mind is that the wood in the area is so thin that a bit of sanding or planing the drawer face will open up the gaps.

This cabinet has been nothing but trouble from the day I started it. I will be very glad when it's completed. I will be giving it to my Mother in law, so I thought I could inlay a small heart, perhaps with her grandchildren's initials on it, over the boo-boo. I also thought I could carve a band-aid and put it over the mistake :-)


img

Re: blew hole in drawer front

#12

lets see it again after running a scraper over it

Bill Tindall

I am not discouraged by what I see. I don't understand the thin part. Is the front veneered?

Scrape it and be gentle and lets see what develops.

Re: blew hole in drawer front

#13

Re: blew hole in drawer front

Mark Salomon

Well....since you don't have too much to lose at this point you can consider putting an inlay in it. I dunno though, if it were me, given that the cabinet has a nice formal look to it with beautiful door panels, and all of the work that you've already invested, I think that I'd just chalk it up to experience and make a new one. BTW, when I chop blind dovetails I always clamp a board behind it to help prevent this from happening. Even with this, though, if the grain runs towards the front you have to be super cautious to not allow the chisel to follow the grain and poke a hole through the front.