Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

Kinda silly, OT question

Posts

Kinda silly, OT question

#1

Kinda silly, OT question

doug f, san clemente, ca

I'm replacing several bulbs in the outdoor lights that illuminate our driveway. The fixtures say not to use over 60 watt bulbs. Question is, if I replace them with 75 or even 100 watt bulbs will my house immediately burn to the ground at the flip of a switch. I'm just looking for a bit more light without changing fixtures.

Thanks for not laughing.

Doug

Re: Kinda silly, OT question

#2

Re: Kinda silly, OT question

Nat Robison

I think that one of the issues, especially in an enclosed fixture, is the amount of heat generated by the increased wattage bulb and the damage it could do to the wiring and/or fixture. This is assuming you're talking about incandescent bulbs.

Are CFL's or LED an option?

Re: Kinda silly, OT question

#3

It's about the heat

David Yoho

Incandescent fixtures have max wattage ratings due to the amount of heat produced by the bulb. If you're looking for more light, your best bet would be to step up to LCD bulbs. They're expensive up front but their strong suit is longevity, they consume a fraction of the energy a standard bulb does, and produce much more light. Heat is not an issue with these either.

Screwing in a larger incandescent bulb may not cook anything today but think of it as a ticking time bomb!

Re: Kinda silly, OT question

#4

Re: Kinda silly, OT question

Bill Howatt

As Nat says the issue is heat and it will in time cook the socket if it is a type of plastic and may overheat wires due to the heat from the bulb not the current draw. On the living dangerously side, you can probably get away with 75W since they aren't much higher than a 60 and if the lights are on at night the ambient isn't as high. However, you know that isn't what is recommended and the extra 15W isn't going to give much more light either.

I would be thinking of a "100W" CFL or larger which produces much less heat than even the 60W bulbs.

Bill

Re: Kinda silly, OT question

#5

Re: Kinda silly, OT question

Jim Dillon

Doug,

Agree with the others that heat is the problem, especially in a confined space. They now make CFL bulbs in "globe" style that are attractive and should work in reasonably protected outdoor lights. Although intended for indoor bathroom globe replacement etc., they are sure more attractive looking than the spiral CFLs. Also available are "candlestick" style CFLs. Normal CFL floods are available as well, but I don't think you are talking about those.

I have replaced six of my outdoor 60 watt incandescent lights with 60 watt CFL globes and no problem (knock-on-wood). Due to the lower heat output, I don't see why you couldn't use 100 watt CFLs. The only problem so far is that they take a few minutes in cold weather to reach full output, but that is not a deal breaker to me. Got my CFLs from the local Borg.

LEDs are the wave of the future, but the initial cost is still a little high, although the long-term payback is excellent.

Jim

Re: Kinda silly, OT question

#6

Re: Kinda silly, OT question *LINK*

John McGaw

CFLs are probably the best/cheapest alternative at the moment. There could be some dealbreakers though, the biggest being the low-temperature characteristics of the bulb. There are special CFLs made for outdoor use which have a lower starting temperature than 'normal' units. I've replaced the bulbs in four of my coachlight-style fixtures with buglight-yellow CFLs and they seem to work ok down to around 10F so far. I left the other fixture, an automatic unit between my garage doors, with a halogen screw-in bulb because I want it to be on and bright immediately and the CFLs I bought take a good five minutes to get up to full brightness. Since the wattage limits given for normal fixtures is based on the heat from an incandescent bulb you should be able to get away with a higher-rated CFL and still be way below any safety cutoff limit.

Not plugging, but the company shown in the link is pretty good and if you catch one of their frequent sales the prices are really quite attractive. They seem to have almost any sort of bulb imaginable.


1000 Bulbs

Re: Kinda silly, OT question

#7

Not so silly after all.  Thanks for the advice.

doug f, san clemente, ca

Re: Kinda silly, OT question

#8

Re: Kinda silly, OT question

Jim Dillon

Doug,

Glad the thread was helpful. One minor correction to my post. I have been getting my CFLs from Costco, not the Borg. Costco, at least in my area, has a nice selection but it varies from time-to-time so your luck may also vary in finding what you need.

Jim

Re: Kinda silly, OT question

#9

Another word of caution

Lee Schierer McKean, PA

If you try to use a CFL lamp in some sensor type fixtures or timer circuits you could experience premature failure of the CFL. Some of the sensor devices and timers use the downstream circuit as part of their control circuit to operate. This is okay with and incandescent lamp as the small control circuit voltage doesn't hurt the filament. However, some CFL's don't like low voltage and will stay in the "start mode" for prolonged periods of time, possibly not even glowing. This will burn out the internals of the CFL rather quickly. I learned this the hard way with a hall light fixture that is turned on/off by an IR sensor switch.

Lee

Re: Kinda silly, OT question

#10

Don't you mean LED lights?

Mike Farinella

>:)

Re: Kinda silly, OT question

#11

Yes - LCD - LED Whatever it takes!

David Yoho

Re: Kinda silly, OT question

#12

Re: Kinda silly, OT question

Jay Lombardo

It won't burn down right away but you will cook the lamp socket and bake the insulation on your house wires, eventually creating a very, very dangerous situation. Too often I have been the electrician trying to drop the fixture and fix this situation. If we get there in time we replace the fixture and pull new wires because they are burnt so far up there is nothing we can do with them.