Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

Drawer fitting with hand plane

Posts

Drawer fitting with hand plane

#1

Drawer fitting with hand plane

Bill Tindall

My objective here is to encourage people to fit drawers, not assemble them and hope they fit, and that it doesn't take exceptional skill or experience to get a perfect fit, one shaving at a time.


I don' t have many positive experiences with a hand plane. Others claim to smooth table tops, joint for glued edges ,etc. all of which are beyond my achievements. My planed tops feature divots at every grain change. A thickness planer and sandpaper is my best friend. However, planing drawer sides to fit is a piece of cake. Any sharp plane will do.

I cut the drawer front to just fit the opening and the back 1/16" shy of just fitting the opening. As described previously, I glue up the drawer in place. Then I slide the drawer over a piece of plywood which is clamped to the bench and plane till it is smooth and the reveal on each side is ideal, about 1/32" each side.

There are two previous steps that make things go well. When making the drawer sides I orient the grain for easy planing in the glued up drawer(plane front to back) and I select poplar that is straight grained. And, with a low angle plane (home made in this case) I chamfer the back edge of the drawer to prevent chip out of the pins which are end grain. An ancient light weight #5 has become my go-to plane but others would prefer a #4 for this task.

Re: Drawer fitting with hand plane

#2

Re: Drawer fitting with hand plane

John M in Mid Mich

That looks like an Ipe plane there, right? Looks nice.

Re: Drawer fitting with hand plane

#3

Are you left handed?

Barry Irby

That picture looks like you are working left handed. I would have to turn it around and go the other way.

I get almost no use out of my planes. I have a similar one to yours but really have never used it. I have several block planes that do serve me well. I would like to get more from them. Thanks for the encouragement.

Re: Drawer fitting with hand plane

#4

Re: Tell a drawer neophyte more please

Henry (Raleigh, NC)

I have made some furniture: beds, casework, boxes, tables etc. To date only one project with a drawer has made the project list. So I am not very familiar with drawer fitting, except with what I have read. Please tell me more.

I can't quite figure out which dimension you are referring to with the measurements you state. You say you make the drawer to within 1/16, and then plane a reveal of hopefully 1/32 all round. Isn't that there with a 1/16 gap divided on the two sides?

Another way to put my question is: to what dimension does your term "within 1/16" refer? I think I understand the 1/32 reveal - if by that you mean a 1/32 gap between the drawer and the case.

Thanks

Henry

Re: Drawer fitting with hand plane

#5

answer to drawer fitting question

Bill Tindall

Background:

A tight fitting drawer can be closed by pushing one corner with your finger and it will slide closed without binding . It is a most satisfying achievement. A too tight fitting drawer can't be closed(or opened) and the owner of the piece will throw it away. Hence, err on the too loose.

Wood doesn't expand long grain and a typical drawer will have long grain running horizontal (drawer width). Wood will change dimension cross grain (drawer height) so this dimension varies with season.

When I rough cut a drawer I make the front to just fit the opening. This task is done by sawing the drawer approximately correct and then planing to get a fit. A shooting board is useful for the end grain planing. The back of the drawer is make a little less wide, 1/16" of less. In other words in the rough fit drawer I want a slight taper front to back. I make the sides about 1/16" less tall than the drawer opening or even less tall if the drawer is being assembled in low humidity or it is an exceptionally tall drawer.

After the drawer is glued up I plane down the sides so that there is about 1/32" reveal on each side of the drawer front and about 1/16" at the top. It is hard to give exact numbers but the goal is: taking into account the imperfections of the case and everything else, plane till the drawer slides in smoothly and the reveal in the front is pleasing. It is less risky making something for yourself because you can always adjust if it is too tight later in the drawer life. (make the bottom removable as is traditionally done so adjustments can be done later if necessary)

Then I shellac, lightly sand and wax the drawer and case sides and wax the runners. A well fit drawer can be effortlessly closed when it all goes well. It is most satisfying.

Sources of failure: While the drawer width will not change with humidity changes(enabling a tight fitting width) if the case bows the drawer may bind on its sides. Hence, I put a slight taper on the drawer width, front to back, so it fits a bit looser in the back than the crisp 1/32 reveal I want to achieve in the front that shows.

The height of the drawer will change with humidity. How much depends on the lumber you used, both species and how it was sawed and dried and how tall the drawer is. I use KD quarter sawed poplar and shoot for about 1/16"-3/32 on the height.

Drawers in modern factory furniture are not fit, but they were in antique furniture. Every time you get to see an old piece examine the drawer reveals and come to your own conclusion of what works and what looks good. I was amazed how small the reveal could be on the sides, and how well it looked, so over time my drawers have become tighter in this dimension. Again I can get by with risking too tight because I can correct the problem if it shows up in a wet season. If you are selling stuff, I am not a source of useful advice.

Re: Drawer fitting with hand plane

#6

I am not sure

Bill Tindall

I definitely write right handed. But I am told I swing an ax left handed. I shear sheep with either hand as is convenient. I guess I have a slight preference to grab the tote with my right hand, if that would be considered right handed planing.

Re: Drawer fitting with hand plane

#7

Re: Drawer fitting with hand plane

Tony - Memphis

Phil Lowe wrote a really good article on drawer fitting for FWW (#173 Nov/Dec 2004) that has helped me a lot. I built a lowboy (in a class with Phil, ironically) and used that article as my main reference when I got to the drawers. We didn't get to the drawers in class, unfortunately. We used "hardware store pine" for our drawer material and by the time it got to Memphis, it was pretty well twisted up. But, I was able to use almost all of it anyway. The techniques Bill describes and that Phil covered in the article were a big help. I had never used pine for drawers, but I guess it was appropriate and I love that smell when I open the drawers!

Tony - who's drawers smell good!

Re: Drawer fitting with hand plane

#8

Left or right handed, ambidextrous....

Barry Irby

What is it when you are neither handed? I can screw things up pretty well with either hand or both.

Re: Drawer fitting with hand plane

#9

Ellis Walentine

Question re: lowboy construction

Ellis Walentine

How did Phil instruct you to attach the sides and back to the legs? M&T joints? Pegged?

Ellis

Re: Drawer fitting with hand plane

#10

Re: Question re: lowboy construction

Tony - Memphis

M&T. No pegs. He actually did an article on that project after I took the class. He had done a non participatory class on that piece at Highland Hardware several years ago and I saw the display piece in the window and really liked it. When my wife saw that he was offering the class, she sent me to the class for my 40th birthday. I'd really like to build another one and avoid all the mistakes I made. Maybe I'll build a high boy and kill two birds!

Tony

Re: Drawer fitting with hand plane

#12

Ambidextrous or cross-dominant

Bill Houghton, Sebastopol, CA

I did some recent reading on this. There are apparently cross-dominant folks, who use one hand for some things, another for others - this sounds like Bill T. - ; and there are ambidextrous people, who can use either hand for anything equally well.

My grandfather on my mother's side was ambidextrous, apparently. My dad used to say, with a tone of quiet awe, that Grandpa could hammer nails equally well with either hand. Hammering seems like such a basic skill, but it calls for incredibly sophisticated motor control. Try hammering an 8d box nail into a 2x4 with your "off" hand.

Re: Drawer fitting with hand plane

#13

Re: Ambidextrous or cross-dominant

Barry Irby

I used to Install 1/4" underlayment plywood by driving small ring shank nails in it on a four inch grid, about 300 per sheet. It was such a dumb boring job I hated to pay anyone to do it. I would go early int eh morning or on the weekend and sit there nailing and nailing. (In the days before air powered staple guns. For entertainment I would nail right handed for a while and then left handed. Tap, wham, tap, wham, tap, wham. then I would hold the hammer out the other side of my hand. Then behind my back. I actually got to where I was good with my left hand, but only for those little nails.

I also had a framing hammer with a really long custom made handle with finger grips. I don't remember now, but the head weighed about 32 Oz and the handle was close to 20". Them men teased me about it because I am only 5'8" tall and that hammer looked like I was wearing a sword in my nail apron. I drove 16d cement coated sinkers all day long, tap, wham. That may account for my sore shoulder today.

I mentioned they teased me about the hammer. But they kept disappearing. I had about four of them. A friend of mine had a handle factory and made the handles for me.