Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Kitchen Cabinet Door Question

Posts

Kitchen Cabinet Door Question

#1

Kitchen Cabinet Door Question

Thomas Skaggs, Foothills of Mount Level

We recently bought a mid century modern house. In the kitchen are 50 year old cabinets that are due for an update. The boxes and face frames are fine. I plan to make new doors and drawer fronts.

The look will be panel-less contemporary doors that will overlay the face frames to look more like frameless cabinets.

To make the doors (and save money) I was thinking of making hardwood frames to edge glue to ply panels and then veneer over the faces and backs to look solid.

I've never done kitchen stuff before but is that construction method ok? For the centers....MDF? Ply?

Thanks

Tom

Re: Kitchen Cabinet Door Question

#2

JL

Re: Kitchen Cabinet Door Question

JL

IMO, I would go with plywood. I don't like MDF in a kitchen - no matter how well sealed. I used MDF core plywood in one kitchen job. It had some problems when it got a bit wet. I used the rest of the sheet to make jigs.

Re: Kitchen Cabinet Door Question

#3

Re: Kitchen Cabinet Door Question

FredD

I agree with JL about the PB , leave it out.

A popular door we used to make was a Hardwood 1x2 skinned front and back which gave you a hollow door and in most cases was lipped, but it would work fine as a overlay door.

We left the frame edge project past the skin area and beveled it and eased the leading edges for a very nice looking door.

If you do it that way put a backing block in the middle running the inside lenght of the hollow part to strengthen the door skin.

That construction gives you a light , very strong door , not prone to warp.

FredD

Re: Kitchen Cabinet Door Question

#4

Clint Searl

Re: Kitchen Cabinet Door Question

Clint Searl

Since you don't have to worry about seasonal movement, consider solid doors made up of edge glued segments. That's what I did when remodeling our kitchen, using river recovered cypress.

I'm curious, when I did mine I made the doors full overlay with exposed hinges, but left enough face frame exposed to accommodate the door swing. If you're going for a complete frame overlay, how will you keep adjacent doors from interfering with each other?

Clint

Re: Kitchen Cabinet Door Question

#5

Mixed Design

Thomas Skaggs, Foothills of Mount Level

Hi Clint,

You are observant! Yes, there will be a conflict here and there. Therefore the overlays will have to be adjusted to permit door swings. I will not be reusing the old external mount hinges and will instead go to Euro hinges. If I can afford them, the soft close hinges would be nice.

Tom

Re: Kitchen Cabinet Door Question

#6

Re: Mixed Design

Barry Irby

If you use a frame with a skin (I think it would be very strong and stable, but have no opinion on the appearance) be sure to take the hinge design into account. Many of the Euro Style hinges require an accurately drilled hole (37mm?) and you would want that to fall completely within the interior frame, not half in and half out.

Re: Kitchen Cabinet Door Question

#7

Re: Kitchen Cabinet Door Question

Thomas S Stockton

Tom

I always have a hard time picturing things without a drawing but it sounds like what you are planning might be more work than you need to do

How I would do it is to glue 1/4 to 3/8" inch edgebanding to the door cores. The edging can easily be attached with strips of masking tape instead of clamps. Do two opposite sides and trim to fit using a router and cut to length. You then do the other sides and after trimming you can veneer. That is if you want hidden edging.

A look I have used before is to attach 1/8" edging to the door after it is veneered so that it is visible, the plus with this option is that you can use high quality plywood or MDF and avoid the veneering unless you have some special veneer you want to use.

With either option you can also miter the edging if you don't want any end grain showing.

Tom

Re: Kitchen Cabinet Door Question

#8

I have done what you propose plenty of times.

Keith Newton----Little Rock, Arkansas

It is time consuming, and I wouldn't recommend that you do it with just a plain veneer face that can be bought in either plywood, or fiber-core, only with a fancy face veneer is it worth the effort / time.

I don't think you will have any problems from the mdf core, with solid edge, and veneered face. It stays flatter.

You can get euro hinges to mount to the face-frames, but I would just start over if it was mine. I can make a new faceless carcass faster than I can deal with finding all the mounting plates for the differing situations, then finding the right place to mount them to get that clean look. I have been using those hinges since the late seventies, and although the catalogs show what you need for any situation, but unless your suppliers up there are better than mine, they won't have a lot of what you need, and not many of the sales people understand the products well enough to be much help.

As for someone suggestion leaving room for the swing, that isn't a problem with these type of hinges, unless the thickness starts getting over 7/8".

Re: Kitchen Cabinet Door Question

#9

With todays plywood quality,

Dick Coers

I would be afraid to use plywood for doors. Warping or twist will be a major issues. I would go with MDF

Re: Kitchen Cabinet Door Question

#10

Moses Yoder

Re: Mixed Design

Moses Yoder

Blum is coming out with some full overlay hinges with integrated soft close feature the first part of this year they said. Currently you have to clip on a somewhat bulky soft close cylinder which sometimes comes off. Check your required door swing clearance carefully; the hinges we use for frameless cabinetry require less than 1/16" clearance for the door to open. We have done doors in the past that were a simple plywood slab with a 1/4" thick x 3/4" wide molding glued to the face, flush at the edges. The edges were then edge banded, making a 1" thick door at the edges but it had a kind of framed look. Just a thought for you ;) We are using more MDF for painted stuff and so long as the sealer and finish are compatible and applied correctly we have not had any problems with them. However, it is a nightmare when you have an installed job and the paint starts peeling at the edges when it gets wet; we only had this problem when using a vinyl sealer.

Re: Kitchen Cabinet Door Question

#11

Funny you should mention it.

Thomas Skaggs, Foothills of Mount Level

No later than an hour after I read your post I recieved an email ad for the new Blumotion Hinges. They look like winners to me!

Thanks

Tom

Re: Kitchen Cabinet Door Question

#12

Re: Kitchen Cabinet Door Question

Steve Jenkins, McKinney, TX.

I've done a lot of doors like you are suggesting. I'd use MDF as it is the best substrate for veneer. If you are concerned about moisture you can use Medex which is a weatherproof mdf. For doors though I don't think it's much of a concern if they are well finished. I've used the same method for making raised panels,mitering the edgeband and making it just 1/32 wider than the raised portion of the panel. Gives a really consistant look from door to door.