Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

need your thoughts on this

Posts

need your thoughts on this

#1

need your thoughts on this

John Lucas

I have all my hand planes stored in a wooden cabinet with drawers. They are in the bottom 2 drawers since I don't do a lot of handplaning any more. I'm having trouble with surface rust on the blades and some other parts. I think it's due to the wood picking up moisture from the concrete floor.

I hope to solve this problem when I finally get around to building some cabinets. I'm going to try and make one that is off the floor just for the planes and chisels.

In the meantime what is your solution. I've tried the FRog stick on pads that put out a coating odor. That seems to work but you don't know when they wear out. Anything I spray on wears off the first time you sharpen the blade.

Re: need your thoughts on this

#2

Re: need your thoughts on this

matt overton

Have you tried the japanese oil wick to just put a light coat of oil each time you put them away?

Re: need your thoughts on this

#3

JL

Re: need your thoughts on this

JL

Several thoughts.

I have a basement shop ("daylight" basement, but still a basement). I continually run a dehumidifier 24/7/365. I've gone through two of them since I've lived here. I have it set on 60%. If you keep the RH lower than 60, you have less problem with rust.

Another solution is silica gel packs (with or without indicator) in the drawers. They can be rejuvenated by baking them in an oven for a while.

Pacific silver cloth or a similar anti tarnish/anti rust liner for the drawers. I have a friend with a collection of "heirloom quality" planes. His drawers are lined with silver cloth as well as having some silica gel packs.

Re: need your thoughts on this

#4

Silica Gel Packs

Todd Nebel

I keep a couple of these in my drawers and replace them when I buy something that comes with them. I've never had any issues, but my basement shop is not that damp to begin with. Recently I started to coat my Lie-Nielsen saws and planes with their Jojoba Oil (similar to Camellia oil) because I started to see a little spotting (I think it was due to being stored in the leather cases).

Re: need your thoughts on this

#5

Re: need your thoughts on this

Ken Oakley-Sunny St. Cloud, Fla

Put some mothballs or flakes in the drawers. Learned it from an old German machinist im the 1960's.

Re: need your thoughts on this

#6

RemOil works for me

Dave Bair, Eaton Rapids, MI

Re: need your thoughts on this

#7

Re: Silica Gel Packs

Phil Joines

The packs can be dried in an oven and reused.

Re: need your thoughts on this

#8

Re: need your thoughts on this

Phil Joines

Can you raise the cabinet on blocks an inch or two?Get some air movement under it.

Re: need your thoughts on this

#9

Re: need your thoughts on this *LINK*

Bill Turpin in WNC mountains

What about rust-inhibiting paper? Used for wrapping of quaility stuff that will be stored for a while. Available from most industrial supplys. Bearings come wrapped in it.


McMaster

Re: need your thoughts on this

#11

Re: need your thoughts on this

FredD

The desiccate packs mentioned and the rust inhibiting paper will work fine.

Pacific Silver cloth will not keep Ferrous metal from oxidizing.

It keeps Silverware from oxidizing because it has thousands of minute particles of Silver embedded in the cloth which reacts first before the Silver does .

FredD

Re: need your thoughts on this

#12

Best Solution:  Out of the Drawers

Ron in Sterling, CT

I have a basement workshop in New England and run a dehumidifier continuously during the summer months to keep the humidity at 55 -60 percent. For years I stored my planes in a cabinet over my bench, and did not have any rust problems. Then I rearranged my shop with a cabinet/bench in the middle of the shop which had several drawers. I moved the planes into the drawers and had instant rust problems. After fighting it for 2 years (and using many of the suggestions listed above) I moved the planes into a new storage cabinet on the wall. Rust problems ended immediately. The moisture was wicking up from the basement floor and creating the problem. I now store "stuff" in those drawers that are not affected by moisture.

The second best solution (already suggested) is to get some air moving under the drawers.

Good Luck,

Ron

Re: need your thoughts on this

#13

Re: need your thoughts on this

George Colonel's Workshop-Havertown PA

Good Afternoon John,

All of my hand planes are displayed on the walls of my Neanderthal Shrine Room. I have had no rust problem there with planes, or other objects like hand saws and chisels. I have had no moisture problem in either of my shop rooms, each of which is fed by my hot/forced air house heat. Your best solution may be to get your planes up higher and to use a dehumidifyer.

George