Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

Finishing Very Curly Soft Maple

Posts

Finishing Very Curly Soft Maple

#1

Finishing Very Curly Soft Maple

Roger T

Morning all,

My current project is a pair of Sheraton end tables with very curly soft maple. All the fitting work is done and I am now in the process of surface prep. I am doing as much prep now, before glue up as I can.

Because of the amount of tearout involved with the machining of these parts, A lot of scraping and sanding is involved. I am using the Norton 3x paper, at 180 grit to get the job done.

My finish schedule will probably be something like this.

Prewet the wood to raise the grain and sand back.

Lightly wet the wood to even absorbtion of the Transtint Dye with sanding back to just leave the color in the curl.

One or 2 coats of Shellac to seal in the color. Level with a grey scotch brite pad.

Final coats will be one of the many Water based Lacquers that are now available. All the finish coats will be sprayed with a STM HVLP sprayer in my basement.

Am I already going to far with the 180 grit, or do I need to continue on to 220 grit to have a flawless finish. I have never worked with wood that has this much figure in it, and dont want to make a mess of this either.

I am open for any and all suggestions at this point.

Thanks much for your insight.

Roger

Re: Finishing Very Curly Soft Maple

#2

Re: Finishing Very Curly Soft Maple

David Yoho

Roger, in general, it sounds like you'll be just fine.

I recently completed a king size headboard for a customer using cherry and highly figured curly maple. I only sand to 150 and end up alright. I start by sanding to 100-grit. I apply a coat of W. D. Lockwood water-based dye of a specific color. This coat will show sanding scratches or any glue on the surface and soak into the figure to highlight it later. I sand this coat from the surface while being careful to remove any previous scratches or glue. This is followed by a coat of a mix of specific W. D. Lockwood colors. Ater this dries, I hand apply at least four coats of Waterlox before waxing and buffing. It works well for me but depending on the solvent for the dye (water, alcohol, or oil), a sealer coat of shellac (de-waxed) can be helpful.

Here's a shot of one of the posts - -


Re: Finishing Very Curly Soft Maple

#3

Sage Advice

Bill Tindall

Practice what ever you choose on something besides the table. This is the sage advice part. The rest is opinion.

Personally I sand maple to 220 to lessen dye take on the flat grain. After the dye stain a coating of linseed oil can richen things up significantly, especially since you will be using the lacquer you specified. The oil must be allowed to throughly dry and it may be incompatible under a water based finish. I would be using a solvent based lacquer to get a brighter appearance. Maybe someone has a water based product that looks as good as solvent based lacquer but I haven't seen it yet.

Re: Finishing Very Curly Soft Maple

#4

Re: Finishing Very Curly Soft Maple

Tony - Memphis

I sand to 220 and hit the end grain areas with 320. I did raise the grain with clear water and sand lightly again. That still doesn't get all the areas, so after I stain, I go lightly with a synthetic pad. I used an oil based finish and added a coat of glaze between layers. Nothing special really. I did lots of samples as Bill suggests. I'd be careful of the oil coat on top of the stain. My experience is that the oil really darkens the end grain areas quite a bit. A trick I learned when dying is to wet the end grain areas with clear water before staining. That helps a little. Some folks apply a wash coat of shellac. I tried that but wasn't crazy about it. Can't recall the stain I used, but I'm pretty sure it was a Lockwood or a Moser (which may be Lockwood) honey amber or something along those lines. Also experiment with the concentration. That makes a big difference.

Tony


Re: Finishing Very Curly Soft Maple

#6

wash coat

Bill Tindall

A wash coat of 0.5 pound shellac followed by 300 or 400 grit sanding will lessen the absorption of the stain in the areas that would otherwise darken considerably. It worked to good effect on some crotch veneer I was working with.

Re: Finishing Very Curly Soft Maple

#7

Re: Finishing Very Curly Soft Maple

Roger T

Thanks for the help guys, much appreciated. The table you made is stunning, and just about the same color as I am wanting to get for my project. If you can think of anymore tips or hints, I would really like to hear them.

Roger