Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

Jet Bandsaw Mods

Posts

Jet Bandsaw Mods

#1

Jet Bandsaw Mods

Steven Bellner

I have a Jet JWBS-18, purchased in 2004. This has been an excellent saw in all regards except one. The lower Carter-like saw bearings are a tremendous PITA to adjust. The bearings are mounted on a bracket, and that bracket is secured to the saw by two allen bolts. The front one is relatively easy to get to, but the back one almost requires the removal of the table to get the bracket properly adjusted. I believe Jet recognized this problem, and re-engineered this part, but the modifications are not backward-compatible.

I was looking at the general layout of the bracket, and thought if I drilled a hole through the table directly above the bolt, I could get a long allen wrench down into the bolt a lot easier than trying to use the stubby wrench that came with the saw. Firstly, has anyone else with this saw had problems adjusting the lower guides? And secondly, does the proposed modification sound feasible? I don't want to simply go start drilling holes in the table top if I am missing something obvious.

FWIW, when I take the time to properly set up the saw, it can resaw a piece so thin it looks like a handplane shaving. I use a Timberwolf 1" 3-TPI PC blade for resawing, and use their "flutter test" for tensioning. They tension out at a much lower setting than the machine indicates. I don't seem to have the flex in the frame I have read others have had. That may be more related to their 16" saw.

Re: Jet Bandsaw Mods

#2

Re: Jet Bandsaw Mods

charles in mtl

A picture could help a lot to understand the problem with the bandsaw.

Re: Jet Bandsaw Mods

#3

Re: Jet Bandsaw Mods

mike

I suggest that you call and discuss this problem with a Carter Tech. Carter is a great company to work with and you will find their tech service very knowledgeable. Good luck

Let us know what they suggest!

Mike

Re: Jet Bandsaw Mods

#4

Re: Jet Bandsaw Mods

Todd Nebel

Hi Steven, I have the same bandsaw and agree it is difficult to adjust the lower bearing plate. This only needs to be done when you change the blade to a different size. I've settled in on the Timberwolf 3/8" blade and haven't had to change my lower bearing plate in years. I find that for "my" typical use of the bandsaw (resawing, cutting blanks for turning, cutting checks in tenons, the occasional circle top/shelf, etc) this size is perfect. I don't do intricate puzzles piece shapes or tight twisties. Also, agree that I can resaw with fantastic precision straight off the fence (minus the resaw bar) on this JWBS-18. I had taken this photo a while ago for somthing else. it doesn't show the inside of the bearing plate where it's difficult to get an allen wrech into, but it does show the outer and the allen key bolt.


img

Re: Jet Bandsaw Mods

#5

Jim Rahbe, Bedford Texas

Exactly�..

Jim Rahbe, Bedford Texas

Steve.

I did exactly what you suggested on my 18� Jet bandsaw. I drilled a small hole directly over the hard to reach allen-head screw. It works great and makes blade changes much easier.

Regards,

Jim R.

Re: Jet Bandsaw Mods

#6

Thanks!

Steven Bellner

I went down to take some pics to post, and I convinced myself this was the way to go in the process. I now have a minor project scheduled for this weekend.

I use a tri-square to set one side of the bracket, hand-tighten the outbound bolt, and then square up the other side with the tri-square, and then try the contortions needed to access the bolt head. Usually end up knocking the bracket out of square in the process. Having that bracket square to the blade is critical to achieving a good cut with this saw.

I am a firm believer of changing blades to the proper size/pitch appropriate for the task-at-hand. The trouble I have had adjusting the lower blade guide has sometimes made me cut corners, and use the blade last mounted. It's not trivial to change a blade, but it isn't rocket science either (except for tightening that back bolt!)

While looking on the interweb for other options, I ran across a fellow who built a box that replaced the lower blade guard, and also hooked it up to his DC. I'll see if I can find that mod and post the link to it. It was a clever solution to 1:) providing a safe guard, and 2) improving dust accumulation on the lower bearings.