Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

Clamp Advice Needed.

Posts

Clamp Advice Needed.

#1

Clamp Advice Needed.

Thomas Norton

I have a shop built slot mortiser and need a bit of help with a clamping idea.

I have the type of clamps,cannot rememeber the name, where you flip the handle and it pivots down to hold the work down. I have 2 of these mounted to plywood squares that have "T" bolts and track.

The problem is I am limited to the thickness I can clamp. The other day I wanted to mortise some slots in 1 3/4" legs and it was a no go. So I did it freehand just to get it done as I did not want to take the time to work out an alternative.

So any thoughts? On some of the commercial models I see some type of post with a clamp on it.

Re: Clamp Advice Needed.

#2

Re: Clamp Advice Needed. *LINK*

Bruce, a MN Galoot

They're called toggle clamps, and my favorite brand is De-Sta-Co. You'll find a wide array of types, sizes and applications if you take a gander


Amazon's offerings

Re: Clamp Advice Needed.

#3

Re: Clamp Advice Needed.

Henry (Raleigh, NC)

I use these De-Sta-Co toggle one my one-off jigs all the time. Here's the basic 'design"

Base piece of plywood - either run against fence of TS/BS or use miter slot of TS/BS, or freehand (BS only); I also use these on similar router table jigs. typically run against the router table fence.

Blocks of necessary thickness (often 2x? or 1x? material), are screwed into place from below. The clamps are mounted onto the top of these blocks, so they need to be positioned appropriately).

Each clamp has about 1" of travel in the head, so that accounts for thickness variation in the piece to be cut, as well as control of the amount of clamping pressure to use.

Mount piece to be cut into/onto sled and presto....

I use this basic design for

- a TS tapering jig

- a jig to create a straight edge on a S2S board with uneven edges,

- router sleds for irregular pieces

and other applications I can not think of right now.

So in essence I elevate the clamp to the right height by mounting it on a plywood sled with a block beneath the clamp. I'm not quite sure what your set up is, but the idea is quite general. Only disadvantage I see is that you lose the thickness of plywood in terms of depth of cut (on a TS at least).

Henry

Re: Clamp Advice Needed.

#4

Re: Clamp Advice Needed. *LINK*

Dave Paine

If you have the T track consider something like this hold down from Lee Valley. Other places have alternates.

http://www.woodpeck.com/msn.html has special nuts for Mitre saw tracks which use standard 1/4in bolts so by changing bolt length you can quickly increase available height.


http://www.leevalley.com/US/wood/page.aspx?p=63315&cat=1,240,41060

Re: Clamp Advice Needed.

#5

Re: Clamp Advice Needed.

Thomas Norton

Bruce,Thanks for the Amazon Link. I think the solution will be the long "Foot". http://www.amazon.com/Large-Toggle-Clamp-Foot-Long/dp/B001ENXI06/ref=sr_1_80?s=power-hand-tools&ie=UTF8&qid=1292773632&sr=1-80

I think this will allow me to clamp different thicknesses without having to change the base piece .

Thanks again!

Re: Clamp Advice Needed.

#6

Ellis Walentine

Thoughts

Ellis Walentine

My first thought is the Maple-Tek clamp, which has been extinct for fifteen years or so. Here's a link to a little write-up we did on it: Maple-Tek Toggle Clamps. I had two of them mounted on one of our horizontal mortisers before the fire. If you ever see anything like them, snap them up. They're the best hold-down clamps I ever had.

Another idea I've toyed for this particular application is these great adjustable clamps I saw at IWF this year. I bought one and love it. If you could just get rid of the jaw with the big pad and screw the handle to your jig, you'd get the benefit of this clamp's automatic adjustability from zero to several inches of thickness without making any changes in the clamp settings.


Other than that, there are various shop-made clamping rigs you can build. I don't have time to dig around for specific designs for you right now, but the idea is to use either a third-class lever or a cam handle, or even wedges to exert the force. For the third-class lever approach, all you need is a bolt, a wing nut and a beam to act as the clamp.

Ellis

Re: Clamp Advice Needed.

#7

Re: Thoughts

FredD

I am surprised a clamp that good would disappear from the market place.

FredD

Re: Clamp Advice Needed.

#8

Ellis Walentine

Re: Thoughts

Ellis Walentine

>I was apparently one of the few people who went to bat for these guys, but despite our rave review and my personal satisfaction with the clamps, he hit some financial hurdles he couldn't get over, and the company went south. I wish I could get a couple replacements. They were great.

Ellis