Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Alright I feel stupid

Posts

Alright I feel stupid

#1

Alright I feel stupid

Dustmaker Mike

So I have the last three weeks of Dec off. It is time to finish the honey do list. On top of the list is the half bath down stairs. I moved the light fixture and the mirror. I put up the molding around the door and the base molding. Then I turned to the crown molding. I set my saw up on the stops for the molding and cut away. Nope it didn't fit it was even facing more down then at a 90. So I played awhile with it then just stopped. Sat down looked on the internet and found out what I did wrong. I had set my fence and saw to do a compound miter then I held the molding in the proper position as it would be on the wall. After a few minutes of looking I figured out I should have laid it flat on the table. Oh well I will finish it in the morning I hope.

Re: Alright I feel stupid

#2

Don't

Don Orr

Feel stupid that is. I wouldn't even attempt crown molding myself. At least you knew when to stop and figure it out.

Re: Alright I feel stupid

#3

Re: Alright I feel stupid

George Colonel's Workshop-Havertown PA

Mike, I am in complete agreement with Don.

Crown molding occupies an occult position in my shop. Its a mystery seldom fathomed, and never personally attempted with anything but real bad results. I look at some of my #3 son's work in high end kitchens and am simply amazed at the speed and accuracy, not withstanding the surface leveling and preparation.

George

Re: Alright I feel stupid

#4

Jim in Burlington Ont.

Re: Alright I feel stupid

Jim in River Oaks, Ont.

I always cut the moulding first, then build the room....works every time

:-)

Take care,

Jim

Re: Alright I feel stupid

#5

Dale Lenz

I like your answer, Jim 

Dale Lenz

>

Re: Alright I feel stupid

#6

Re: Alright I feel stupid

Jesse Cloud

Getting flummoxed by crown molding is no reason to feel stupid, but thinking you will ever "finish the honey do list" is just crazy :D

Re: Alright I feel stupid

#7

Not to feel bad

Bill Houghton, Sebastopol, CA

Crown molding is famously The Worst trim work. I'm sure there are lots of journey level carpenters who would freeze solid if assigned to do that.

Re: Alright I feel stupid

#8

Re: Not to feel bad

FredD

"I'm sure there are lots of journey level carpenters who would freeze solid if assigned to do that."

Not if they are actually Journeymen as opposed to those who just say they are and or bought a Union Card without any prior experience, it happens all of the time, sad to say.

For Mike's Crown Mould project , if you cope the inside corners you will have much better success at a good fit.

FredD

Re: Alright I feel stupid

#9

Yes, you're right; I wasn't clear

Bill Houghton, Sebastopol, CA

I was thinking not of properly trained union folks, but people who swing a hammer (or a nailgun) just framing houses.

Re: Alright I feel stupid

#10

(Message Deleted by Poster)

Chuck Lenz

Re: Alright I feel stupid

#11

Nope

Dustmaker Mike

I was using a miter saw to cut the crown.

Re: Alright I feel stupid

#12

Re: Alright I feel stupid

matt overton

When figuring compound angle, be aware of the spring angle of the moulding. That is the angle relative to the ceiling. Not all crowns are created equal, they are angled at 38, 45, or 52 degrees based upon the height of the room intended for, in order to have the onlooker see the full profile while standing in the room. The higher the ceiling the greater the spring angle. This changes the compound cut.

Re: Alright I feel stupid

#13

Re: Alright I feel stupid

Glenn Madsen---in SF Bay Area

So tell us, when you're finished with the room, and it looks right, that you still feel stupid.

I have a friend, early thirties, that does this stuff professionally. Watching HIM makes me feel stupid. There are a hundred tricks to getting this stuff right, gained by watching a pro, doing a dozen rooms, and watching other pros. That you might have made a couple of early mistakes is pretty much expected.

When you're done, you'll find the wife showing the room off to her friends... :)

Re: Alright I feel stupid

#14

Lee Grindinger

Coping with crown

Lee Grindinger

Fred is dead on, don't mess with trying to miter inside corners, coping is far better.

Re: Alright I feel stupid

#15

Coping I am not sure how to do it

Dustmaker Mike

I will look around tonight and see what I can find on how to do it. I have the grand-kids this weekend so I am out smarting them and taken them sledding of course it is a very big hill they have to keep walking up :D I figure after two hours of going up and down the hill in the cold when I say bed tonight they will be out pretty quick.

Re: Alright I feel stupid

#16

Re: Alright I feel stupid

Bob Willey

I would recommend you watch a demo video. The site is cutncrown.com.

I used his method and some home made jigs similar to what he shows. I did my living room,dining room, and master bedroom and it came out perfect with no coping required.

Re: Alright I feel stupid

#17

Re: Coping I am not sure how to do it

Barry Irby

I find putting up Crown to be fairly understandable and not terribly difficult. Once I figured out that I had to turn the piece upside down in the saw it all fell into place. (I have a power miter saw, but it is not a compound one.)

Coping is also fairly straight forward. You butt one piece square into the corner and then cut a miter on the other piece as if you were going to cut an inside mitered corner. Then you cut away the part of the piece that the saw angles. Take a pencil and mark the edge that defines the end of the surface or the piece. Under cut the end and then it will fit against the butted piece.

I bet there are a ton of video's on You tube. This is easier to do and describe.

Also, I cut with the blade in the coping saw so that it cuts on the pull stroke and with the handle under the piece. If you have a really sturdy saw you can use the push stroke, but it relies on the strength of the frame to tension the blade.

Re: Alright I feel stupid

#18

Re: Coping I am not sure how to do it

FredD

Coping like Barry described works fine that is the way it's be done for centuries and the way I did it until Bosch came along with their barrel grip Jigsaw.

This speeds the work greatly , all you do is let the saw rest on the Miter face as you cut which gives you all of the under cut needed.

If you have a Bosch , install their scroll blade which is about a 1/8th inch wide.

Takes a little practice , but so does any wood work operation..

There are a few tricks that make it easier to do .

When first starting in a room, cut the Crown so it runs full length with square end cuts on the two long walls first .

Then the short walls receive a piece coped on both ends.

This piece is cut a little long , about a sixteenth of a inch and you place one end in place and pull the center out until the other end rest's in place and let go and it snaps into place and fit's like a glove.

FredD

Re: Alright I feel stupid

#19

Re: Coping I am not sure how to do it

Barry Irby

Would have never thought of using a powered saw for this. Stinking thing on my part. Locked inside my own head. I will have to give that a try.

To me, the process is actually pretty easy once you get your head wrapped around it. Like Fred said, you can actually cut the pieces slightly long and spring them in and they actually get a little bite into the piece they are butting.

To me, the hardest part was going around the room without changing the angle of the molding to the wall and ceiling. That is, not getting it all headed to the corner at the same angle. On big complicated jobs I sometimes used a chalk box with white chalk. You could just barely see the chalk but that was enough to go by. Don't use blue or red chalk, they float through the paint.

Re: Alright I feel stupid

#20

Re: Coping I am not sure how to do it

George Koch

As Barry mentioned above, you should first determine how far down the wall the bottom of the crownmold, of any size, should be and mark that on the wall, especially at the corners. Another trick is not fasten neither piece close to the corner until they are both in place so that they can be moved up on the wall or in on the ceiling to close the miter or cope. I prefer to cope all the interior angles, because with any movement or shrinkage the joint opening will be 50% and even less if the cope is sprung into place as mentioned. George

Re: Alright I feel stupid

#21

Re: Coping I am not sure how to do it

FredD

About marking for position of the Crown relative to the ceiling Barry , over the years I found that a snap line gives you a reliably straight line , which in many cases doesn't conform to the ups and downs of poorly built dwellings.

I cut a piece of the crown five or six inches long and hold the upper and lower flats against the ceiling and wall and mark the bottom or top of the Crown 's position every few feet and then if you have ups and downs , so does the Crown which is less noticeable then forcing the Crown to march in a straight line , when the Ceiling doesn't.

On the other hand , you can get Caulk in case lots for less. ;-))

FredD.

Re: Alright I feel stupid

#22

Re: Alright I feel stupid

Barry

Crown molding can be tough. There are some good books on installing crown, that you can find at the big-box stores like Lowe's and HD. First, if you are cutting just three four pieces of crown, just do it on your tablesaw. Cut it upside down, propped against the miter fence at the same angle it would fit against the wall.

Assuming the room is a rectangle with no outside miters, cut and install the piece opposite the door first, straight cuts on each end. Then do the wall to the right or left, your preference. Cope the end next to the piece that's already installed. Once that end fits, cut to length with a straight cut to the other end. Repeat for the next piece. The last piece will need a coped joint on both ends, so buy a little extra molding. It's hard to get this right the very first time. If the room has an outside corner, do those pieces first. Seeing all of this illustrated in a good book on installing crown really makes it a lot easier. Good luck.

PS You could always just buy those little corner blocks and put up the crown with all straight cuts, butted against the corner blocks. But that's almost cheating, unless you happen to like the look.