Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

Issues with CrystaLac grain filler?

Posts

Issues with CrystaLac grain filler?

#1

Issues with CrystaLac grain filler?

DouginDenver

In an age when even a toaster comes with 30 pages of instructions, CrystaLac sets a new standard for minimal and poor instructions. All the instructions say are dries fast, wipe on and "trowel" off, and sand between coats. Not a word about how long to wait between coats, how long to wait before topcoating, and, most impotantly, any topcoat compatibility issues. It is a "waterborne" product, and looks and acts like slightly thicker water based Varathane - kinda like thick milk but dries clear. Before I contact the comapny, I'd thought I'd ask if anybody here knows of any topcoats that will not adhere to it well or has any other advice.

Re: Issues with CrystaLac grain filler?

#2

Re: Issues with CrystaLac grain filler?

Steve Schoene

Haven't used it, but have heard a number of comments about it suggesting it shrinks quite a bit. I guess that means to use it you should clean off the first coat and then give it a rest to get the shrinkage of the first coat completed before you apply the second.

Personally, I much prefer oil based pore filler--plenty of working time so you seldom have any serious sanding to do just scrape and wipe off the excess.

Re: Issues with CrystaLac grain filler?

#3

Re: Issues with CrystaLac grain filler?

Mark Mandell - Gone Round In Jersey

Hi Doug,

I've used it for years to do filled pore finishes on walnut; haven't had any problems. My routine goes like this:

1. Sand the surface to 180 and vacuum off well.

2. Apply a spit coat 3/4 lb cut of dewaxed shellac; let dry for 2 hours.

3. Apply a first coat of Crystalac filler and work into the pore with a plastic straight-edge going first with, then at an angle to, the grain. The "squeegee" will remove the excess. Allow to dry 2 hours.

4. Resand with 220 paper.

5. Apply a second coat of filler, going lightly with the squeegee to leave more filler on the surface. Allow to dry well (2-3 hours).

6. Resand with your final grit paper on a flat wood block moving with the grain. I find that a power sander's platen surface tends to flex too much for a truly flat surface. The dried filler sands easily, so this isn't the chore that it might sound like. Shaped edges and molding profiles can, of course, be a pain.

7. Apply your finish. I've used shellac, NC lacquer, oil poly, and good waterbornes over Crystalac with no issues. Remember, however, that any waterborne finish applied to a raw-sanded surface will tend to raise the exposed wood fibers. Perhaps this is what people read as the filler shrinking. Another spit-coat of shellac before application of a waterborne finish usually solves this problem for me.

Re: Issues with CrystaLac grain filler?

#4

Which oil based filler?

DouginDenver

Which one do you prefer? I'm just starting to play with fillers. You are correct about Crystalac shrinking.

Re: Issues with CrystaLac grain filler?

#5

Re: Which oil based filler?

Steve Schoene

I think the best I've uses is Sherwin Williams. It's filler is silex which becomes more translucent than most, and shrinks very little. Problem--only in gallons and only from the industrial type stores not the retail stores. Old Masters seems OK, and has a high proportion of silex. The Behlen shrinks a bit more but has been widely used. It comes very thick--so it goes far if you thin to the consistency of heavy cream using naptha.

Re: Issues with CrystaLac grain filler?

#6

A couple other questions

DouginDenver

I wondered about the Behlens' claimthat I need their special thinner to thin it. So Naptha is fine?

What are the range of things I can use to tint Behlens? Can I use liquid Transtint dye from the bottle?

Re: Issues with CrystaLac grain filler?

#7

Re: Which oil based filler? *LINK*

FredD

Any S-W store carries this or can get it.

http://picasaweb.google.com/FredD17209/SWFiller?authkey=Gv1sRgCK_gqKuW_5WWtQE&feat=directlink


http://picasaweb.google.com/FredD17209/SWFiller?authkey=Gv1sRgCK_gqKuW_5WWtQE&feat=directlink

Re: Issues with CrystaLac grain filler?

#8

Tint

Mark Mandell - Gone Round In Jersey

Transtint will not do well with oil-based products. Jeff does have an adment to use Transtint with oil finishes, but I think he specifies that it's only for use with clear finish coats rather than stains. He would , however, be the best one to ask.

Re: Issues with CrystaLac grain filler?

#9

Re: A couple other questions

Steve Schoene

One good source of pigment that is easy to find is artist's oil paint. The earth colors--raw and burnt umber, raw and burnt sienna, yellow ochre plus van dyke. Powdered pigment works (I ended up with about a lifetime supply when I visited Olde Mill cabinet shop some time ago) but more effort mixing is required. Universal Tinting Colors UTCs also work.