Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

bow front drawers-2 down 7 to go

Posts

bow front drawers-2 down 7 to go

#1

bow front drawers-2 down 7 to go

Bill Tindall



The center drawer is dovetailed and fitted as is the right drawer which is hanging. Still to go is veneering the front and adding cock bead.

The bow front has added a multitude of complexity to drawer making, especially given that this if my first. Note I have left the drawer front back flat to aid dovetail marking, veneering and just plain holding. It will get its curve sawed just before gluing it together. The half blind pins have been slow to chop. Waste removal is slower than for a flat front drawer where "aids" can be employed. It's all hand work.

I have one problem to solve, cutting the drawer bottom groove. Is there a router bit akin to a rabbit bit that will cut variable depth gooves- in this case 1/4" by1/4" deep?

Re: bow front drawers-2 down 7 to go

#2

Moses Yoder

Re: bow front drawers-2 down 7 to go

Moses Yoder

That will be a nice piece and lookin' good so far ;) I know you can get slotting bits that will make your groove in several passes and perhaps if they make it, in one pass. You groove might be deeper than 1/4" though with the slotting bits, so make sure you groove it before cutting the bottom. I know Stanley also made a tool to cut a curved rabbet with a special plane, I think for only about $600, perhaps Lee Vally will make one that does rabbets and grooves ;)

Re: bow front drawers-2 down 7 to go

#3

Re: bow front drawers-2 down 7 to go

David Yoho

Looking good there, Bill. I didn't do any looking but I seem to remember one of the bit companies that sold guide bearings that would change the depth of cut for slot cutting bits (just like those for rabbet bits). I bet if you do a little digging, you'll turn something up. Maybe you can even source a bearing locally with the right O.D & I.D. and swap it out for the original. These bits usually cut to 3/8" depth. I know on the two I have I can remove the tiny bolt that holds the bearing on and change it.

Re: bow front drawers-2 down 7 to go

#4

Re: bow front drawers-2 down 7 to go

Thomas Norton

Would a Slot Cutter for a router work? You cou vary the depth with the bearing choice.

Re: bow front drawers-2 down 7 to go

#5

Re: bow front drawers-2 down 7 to go

Thomas Skaggs, Foothills of Mount Level

Bill,

I'm sorry that the fronts of your drawers are bowing so much. But oddly enough it might be a good look. ;-)

Tom

Re: bow front drawers-2 down 7 to go

#6

Re: bow front drawers-2 down 7 to go

Jesse Cloud

Beautiful piece Bill! Hope you will continue to post progress pics!

I agree that there should be a slot cutter with interchangeable bearings. My CMT set has a removeable bearing.

If searching for that is a hassle, I can think of two other methods:

1. Take any slot cutter bit and shim the drawer back with tape or a strip of wood to achieve the desired offset for 1/4 inch depth.

2. Since the poplar will be veneered and not show, just cut the bottom off, run a 1/4 inch rabbet on a piece and glue it to the bottom. Run a flush trim over the bowed area to clean up.

Re: bow front drawers-2 down 7 to go

#7

Haven't done this, but I've seen it described

Bill Houghton, Sebastopol, CA

My hardware store sells nylon bushings in various IDs and ODs; and I imagine a bearing shop would have even more choices. If you can't find the right bearing, you might be able to add a bushing to the outside of the slot cutter's standard bearing.

When I first saw your photos, by the way, I thought, "Dang! That drawer front is thick! I wonder if he's doing a secret compartment in it or something?" Your text explains it - keeping it thick and thus flat until you've done all the joint work on it is one of those ingenious ideas that's stunningly obvious only after someone else - like you - thinks of it.

Re: bow front drawers-2 down 7 to go

#8

Re: bow front drawers-2 down 7 to go *LINK*

Hank Knight

Bill,

I've enjoyed following your progress on this piece. You do very nice work.

I had the same issue with slot cutters you seem to be having. I found that even the shallowest slots cut with standard slot cutter set-ups were too deep for letting panels or drawer bottoms into thin stock. Lee Valley sells a slot cutting set for small boxes that does the trick. There's one that cuts a 1/4" slot from 1/4" to 5/16" deep. See link below.

Hank


Box  Slotting Set

Re: bow front drawers-2 down 7 to go

#9

Re: bow front drawers-2 down 7 to go *LINK*

wilbur

Hi Bill,

Have you considered getting a plow plane of some sort? A Lee Valley plow plane would be perfect for making 1/4" x 1/4" grooves, easy to use, and a lot nicer and a lot more fun than using a router. You can also pick up a used Record 044 or 043.


Lee Valley plow plane

Re: bow front drawers-2 down 7 to go

#11

will it make a dado on the concave drawer front?

Bill Tindall

I would cut them on the table saw if all the cuts were on flat stock. But the dado to inlet the drawer bottom into the concave drawer front has me stumped.

Re: bow front drawers-2 down 7 to go

#12

YIKES!  Lee Valley shipping

Bill Tindall

Went to place order and they wanted $11.50 to ship a 1 oz $30 router bit. Declined on principal.

I think I can just chisel the dado into the concave front like string inlay is done. I will deep score the boundary lines with marking gauge and whack away with 1/4" chisel. It would be nice to know how it was done in days of old.

Re: bow front drawers-2 down 7 to go

#13

Re: will it make a dado on the concave drawer fron

Barry Irby

This is a crazy Idea, but how about taking the cutoff from making the front concave and double stick tape it to your TS table. Raise your 1/4" dado blade a 1/4" above it and slide the piece across?

Re: bow front drawers-2 down 7 to go

#14

Re: will it make a dado on the concave drawer fron

wilbur

Forgot about the concave surface -- sorry.

In that case, a purpose-made scratch stock would be a good option. Hank Knight posted a really good article on how to do this in the past.

Re: bow front drawers-2 down 7 to go

#15

Re: YIKES!  Lee Valley shipping

Jesse Cloud

If you are not in a hurry, Lee Valley usually offers free shipping around Christmas.

The scratch stick idea is probably how they did it in the old days. A router plane would probably work, too, since the radius of the bow is not that tight.

Re: bow front drawers-2 down 7 to go

#16

Ellis Walentine

Two answers

Ellis Walentine

If the curvature is an arc of a circle, you can make a wooden plow plane with a curved sole matching the radius. That is a relatively simple tool compared to the specialized planes that carriagemakers used for grooving wheels and carriage parts.

Other than that, put a slotting cutter into a table mounted router and make a fence that is curved to match the inside radius of the drawer fronts. Drill a hole for the bit with a Forstner bit. Set the fence for the depth of slot you want. Rout.

Ellis

Re: bow front drawers-2 down 7 to go

#17

How about...

Brad Chenoweth

a drawer slip simply bent to the drawer front? A slip thin enough to bend might not be strong enough, though. Just my .02

Brad, cozyin' up to the woodburner in NE Ohio

Re: bow front drawers-2 down 7 to go

#18

How about....

DouginDenver

I would not try this idea with a full size router, but I would at least consider it with a small liminate trimmer size router if you have one. The base on such a router is small enough, and your curve large enough, that to a small router your curve it not too much different than a flat surface. What if you cut a strip of 1/4" ply to use as a "flexible straitedge", and clamped it to your curve, and ran a small router aginst it with a straight bit just like you might do if the drawer were flat? It's one of those things I'd have to feel in person to see if it seemd safe, but in the abstract it seems like it might be fine.

Re: bow front drawers-2 down 7 to go

#19

curved fence

Bill Tindall

That is an attractive idea. I already have curved patters from the other operations that can be employed for the task.

Re: bow front drawers-2 down 7 to go

#20

now that is novel

Bill Tindall

and worthy or further consideration

Re: bow front drawers-2 down 7 to go

#21

that will work

Bill Tindall

A 3/8" strip would be adequate and it will bend to the gentle radius required.

Re: bow front drawers-2 down 7 to go

#22

I agree

Bill Tindall

And I have a trim router for the task. I never was fond of the large diameter of slot cutters and I don't have a router will slow down. But a trim router with a 1/4" bit would be no problem. And it matters not if the slot is 5/16 somewhere and 1/4" somewhere else.

Re: bow front drawers-2 down 7 to go

#23

Re: bow front drawers-2 down 7 to go

Phil Smith

Pattern route the draw front groove. Use slotting cutter with bearing below the cutter in router table. Attach drawer front bottom edge to pattern that has correct offset to give you the depth of cut that you want. Should be easy to mill slot.

I have 1/4" 2 wing slotting cutter if you need to borrow one.

Re: bow front drawers-2 down 7 to go

#24

Re: bow front drawers-2 down 7 to go

FredD

The bit you need is used for cleaning out flooring grooves in place.

It comes with or without a bearing ,which you need and the one that cuts a 1/"4 wide by 3/8ths" deep may have to be back ordered for a week or so.

But there is two more that will do the trick at 1/4" deep or 1/2" deep that may be in stock.

That 11.50 S@H of Lee Valley's must be for just really small stuff , I would hate to order a Sledge Hammer at those prices.

http://www.eagleamerica.com/product/v149-1202b

FredD

Re: bow front drawers-2 down 7 to go

#25

Lee Valley shipping

Bill Houghton, Sebastopol, CA

"That 11.50 S@H of Lee Valley's must be for just really small stuff , I would hate to order a Sledge Hammer at those prices."

Like most online vendors, LV shipping rates are based on the amount purchased: $8.50 up to $20, $11.50 $20-120, $13.50 for $120 and up. This is up from what I got used to a few years ago - but what isn't, other than my energy levels?

They do have their free shipping events several times a year - more, I think, than most online folks; when you can wait, or anticipate needs, they're quite handy.