Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

For Drum Sander Owners

Posts

For Drum Sander Owners

#1

For Drum Sander Owners

Mark Mandell - Gone Round In Jersey

For those of you who get tired on having to clean burn streaks from your workpiece and abrasive warps, we may have some progress in the future.

I had a long discussion on the subject with a JET tech on Friday during which I suggested that they (JET) bring their abrasive products into the 21st century with product, like that used in the industrial context, that resists wood fiber and resin-loading that lead to the burning. People running TimeSavers and similar machines do NOT change out their abrasives after putting 2 boards through the damn sander. The cost of abrasives would skyrocket.

Tech told me the issue would be raised at the next product review meeting.

Stay tuned.

Re: For Drum Sander Owners

#2

sounds like someone has a product for sale

ron

Re: For Drum Sander Owners

#3

Re: For Drum Sander Owners

Thomas S Stockton

Mark

Using newer technology in the sandpaper will help some but the big difference between a wide belt and a drum sander is the amount of surface area of the sandpaper. The wide belt has way more and the way the belt is not in constant contact with the sanding drum means that the sandpaper stays a whole lot cooler than on a drum sander so it is less likely to burn.

If your getting burning after two boards you're probably pushing the machine too hard and trying to take off too much too fast. I also find that once I char a roll of paper on a drum sander it is shot even if I soak it overnight and clean it. Some woods are also just prone to burn, cherry is a good example, I just sand to 120 and do the rest with a random orbital or by hand.

Tom

Re: For Drum Sander Owners

#4

Re: For Drum Sander Owners

Dave Paine

I have experienced more burning of strips than I care to think about. I switched to the Klingspor blue zirconia abrasive. More expensive, but a huge improvement. Highly recommended if you intent to continue with your present drum sander. Less heat and less cleaning needed.

I did not get any burn stripes with the zirconia and careful sanding - taking off 1/4 turn or less at a time.

I later switched to a under-the-table mounted drum sander. Even less heat.

I think one of the reasons for the heat in the top mounted drum sanders is that the drum itself provide the pressure to hold the piece between the drum and table. In my Performax the rollers are spring mounted. I feel if the roller were fixed and the drum could be adjusted to be just slightly higher than the rollers, we could do more to contol heat.

We will still need good sandpaper. I have tried several brands. I like Klingspor abrasives in general, and as noted above really like the zirconia.

Re: For Drum Sander Owners

#5

Re: For Drum Sander Owners

Chuck Jurvelin

I find that too many people try to use their drumsander like a planer and try to remove too much too fast. I don't have the facilities for or the budget for a wide belt sander, so I had to learn to plane first and then take numerous light passes thru the drum sander to achieve a satisfactory surface and then progress to a random orbit followed by hand sanding before finishing. Time consuming, but the only way to get the right finish. I might add that sanding in any form is the most boring part of any project,but it separates a good job from a bad one !!

Re: For Drum Sander Owners

#6

Bob

Re: For Drum Sander Owners

Bob

I found that burning would happen no matter what grit I was using when I tried to use my drum sander as an abrasive planer, i.e. trying to remove lots of material quickly. Since I switched over to using it just for finish sanding I rarely get burn marks.

Typically I use my planer to get parts close to final size then run them through the drum sander with 220 grit on the drum to clean up the planer marks and get the parts to final dimension. I always run parts through the sander at an angle of maybe 10-15 degrees, otherwise the paper would start to burn right away. That seems to minimize the heat buildup since you are only using any portion of the drum for a short time then angling on to the next area. I'm also taking off minimal amounts maybe 1/8 turn per pass but since the parts are already close to final dimension it only takes one or two passes per side to finish off. After the drum I hand sand the pieces with 180 to clean up the drum sander marks.

I agree the Performax type paper sucks, funny though the paper I have from them that came with the machine is the same model number but from years ago and way better quality than the current batch.

Bob