Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

ripping narrow stock

Posts

ripping narrow stock

#1

ripping narrow stock

Jerry Gibbs

I am now using the guard on the table saw, since it has a vacuum pickup which I like. The guard interferes with narrow rips. I have to use an auxiliary fence ( a flat piece of 1/2 ply) because the standard fence can't get close enough. This is no problem. The guard interferes with holding down the piece. For example if I am ripping a 1" piece in half, I cannot get a push stick/hold down on the stock. To safely control the stock I have to remove the guard. Any suggestion?

Re: ripping narrow stock

#2

Re: ripping narrow stock

ThomD

When ripping narrow bits, I normally rip it half way and flip it. I like to do this work out of doors for dust and headroom. Often where the rips meet, there will be a pooch. Sorting that out improves the overall quality of the work. I tend not to rip pieces that are both short and narrow on the table saw.

Re: ripping narrow stock

#3

the solution

Bill Tindall

Use a narrow kerf (1/16") 40T 7 1/2" blade. I am fond of the one made by CMT as it leaves a nice cut. However, anything you find at Lowes will do. This kind of blade exerts little force on the piece bing cut so there is ample control of the work.

Also use a Gripe- tite guide from Mesa Vista Design. Each year at IWF the Mesa person rips miles of thin stock using this combination as a demo.

A further suggestion will be to leave this small blade on the saw. It does almost everything you will want in sawing, safer, again because of the vastly less force on the piece being cut.

Re: ripping narrow stock

#4

Re: the solution

Thomas

Bill, is the benefit only because of the narrow kerf, or is the diameter of the blade also in play? The reason I ask is because I have a sawstop and doubt the smaller blade would work (at least in tandem with the Sawstop advantage). I never thought of a narrow kerf 10".

Re: ripping narrow stock

#5

ripping narrow stock   Watch this video *LINK*

del schisler

watch this video. It will show you a trick on riping thin stock . It is by bob neil


http://www.youtube.com/profile?user=InTheWorkshop#

Re: ripping narrow stock

#6

Moses Yoder

Re: ripping narrow stock

Moses Yoder

The brand name of the gaurd slips my mind but I think it is made by Delta. Half of the guard can be flipped up out of the way while the other half is still on the table. This is a safe way to rip thin stock. I make my own push sticks out of scrap 3/4" plywood and sometimes rip right through them. If you rip half way and pull it out you should turn the saw off before pulling it out, or maybe you are not using a splitter with the anti-kickback pawls.

Re: ripping narrow stock

#7

This is exactly what I do

David Yoho

I learned this technique from Charles and have used it since. It's also great for those times when you mill a profile on the edges of several boards that might be different widths using a router and then need to rip them all off the exact same width to use as trim pieces.

The good thing is the cut-off falls away from the blade, where there's nothing to bind it, and you're not working it between the blade and the fence.

Re: ripping narrow stock

#8

Re: ripping narrow stock

steve mackay

I rip 1" (and WAY smaller) day in and day out. I rip half way, flip end over end and cut the rest. I need to run a block plane or sanding block down the cut edge but it keeps my fingers WAY out of the way.

Re: ripping narrow stock

#9

Re: the solution

Bill Tindall

I don't know. But the 7 1/2" thin kerf CMT or Stehle (the best of what I have evaluated) is the blade that stays on my 10" saw. Almost no cutting resistance, leading to great control of the work piece, especially for thin or narrow stock, vastly reduced kick back potential and less dust and noise. On numerous occasions having done what you are wanting to do, I would be mounting the CMT or Stehle on the saw and having at the task.

There are various devices for pushing the stock. Personally, I would use a push stick, thinned appropriately. For less than 1/4" I push up to the blade and then pull the rest through. It is not at all scary with the small thin blade. It is with a 1/8" wide aggressive tooth 10" blade.

Re: ripping narrow stock

#10

Re: the solution?

Denny

I asked Freud tech about this approach for cutting plywood, here's what they replied:

"First I would n0t recommend putting a 7 1/4" blade in a 10" saw. The tip speed will be way to low which could cause a serious accident. In a circular saw the D0760X will give you a good cut but not as good as a LU80. To get that you need the LU79R007 which is a 7 1/4" version of a LU80.

Jim"

Denny wrote:

Will the Diablo D0760X mounted in a tablesaw do as well as the Freud LU80R010 for �� plywood? If it�s the same quality cut, I could buy them as disposable blades.

Thanks,

Denny

Re: ripping narrow stock

#11

try it and judge for yourself

Bill Tindall

There is almost imperceptible cutting force on 4/4 lumber when using the blades I recommended. Low forces lead to better control, less tendency to throw stuff, less tendency for kick back, etc. How the hell low cutting forces translates to an INCREASED safety risk is beyond me. I haven't had a kick back or thrown cut-off since going to these blades.

But, if you think that a 10" 1/8" kerf blade with big combination teeth does just fine ripping 1/8" strips go for it.

Re: ripping narrow stock

#12

Re: try it and judge for yourself

Denny

Bill,

I have tried it, it seems safe enough to me. I was just passing on the "official" word from Freud...

Denny

Re: ripping narrow stock

#13

Jesper, Denmark

Re: It's really quite simple.....

Jesper, Denmark

Mount feather boards on the fence to hold the stock down and on the saw to hold the stock against the fence. Use a push stick and accept that it will get cut to the right width in the process.

The standard guard probebly will need to come off for this operation.

Re: ripping narrow stock

#14

thanks...

Thomas

Thanks Jerry, for bringing this topic up. I've had 2 'accidents' on the table saw in the last 2 years (not really accidents, they were my stupidity) and this is one of the tasks that still makes me nervous. I find myself using my bandsaw a lot more.

Thanks Bill for the suggestion too. I wish somebody would chime in about whether or not the diameter of the blade is a factor in reducing the force. I will soon be buying a 1/16" kerf blade (of the 10" sort though) and trying that. If it helps, it's worth it. One of my 'accidents' happened when I was pushing very hard to get a narrow piece through. Keeping my blades sharp would have helped there too. Even a WWII needs sharpening occasionally.

And thank you Del, for the video. I watched it at school yesterday, very quickly, while the kids were taking a test. I'll need to watch it again, with sound, but it sure does look like a winner.

Happy Thanksgiving folks...

Re: ripping narrow stock

#15

Re: ripping narrow stock

FredD

That practice of cutting half way and "flipping it" unless your stopping the saw between flips is far more dangerous in my opinion then pushing it through with a controlled and practiced move with a push stick.

Your reaching over a spinning blade and picking up stock to rerun and hoping you don't drop it into the blade while you at it.

I stopped more then one Cabinetmaker/apprentice from doing just that.

If I need repetitive narrow cut strips , I cut them from a wide board one at a time using a push stick made by me and between each cut , I run the mother board through the jointer to smooth the cut edge and do it again.

I do not try this with stock so narrow , I cannot control it with my left hand, so I will use the rip saw with a power feed for the cuts that make your hair stand up.

FredD