Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

Dumb Waiter

Posts

Dumb Waiter

#1

Dumb Waiter

Gary Smyth

I have been asked by a relative (No pay to me - or insurance liability either) to build and install a food/medicine dumbwaiter in a 15� x 20� space formerly occupied by a duct laundry shoot. The distance is about twenty feet (fifteen feet opening to opening). I view the end stations as a woodworking and framing problem. I feel confident I can do that. The space between floors I�m thinking I can use garage door telescoping raceways so that I can get them through the existing opening without further breaking a wall. That part appears to be a straight shot. The car will be a wood frame box capable of supporting itself and ten pounds contents, level, using casters, pulleys, belt, rope, cable to run the interior section and must not bang around or get hung up between floors. Of course, some of this can be amended depending on what I find in the space when the laundry shoot goes. My concern is how to stop the car accurately at both ends without grinding the motor/burning it out. I�m thinking a small, slow low torque/slow start winch motor with a suitable cable and pressure switch to kill the power to the motor at either end. Maybe I can devise a light to signal arrival! It will be the same person running and receiving the contents and will not be able to see the arrival of the car. If you have thoughts I want to hear. Please, do not supply commercial units as a reply, I want to try this. This is a test. Oh, and the budget is $1000 max, about 1/3 the cost of manufactured units.

Re: Dumb Waiter

#2

Jim DeLaney, Austintown, Ohio

Re: Dumb Waiter

Jim DeLaney, Austintown, Ohio

Just as an idea - what about using a screw drive garage door opener, with extra lengths of screw?

The box could be attached directly to the drive carriage, and just run up and down the shaft - maybe some dolly wheels on each side to keep it centered in the shaft.

The GDO's limit switchs would start & stop it accurately.

Re: Dumb Waiter

#3

Re: Dumb Waiter

Barry Irby

Literally about forty years ago a friend and I were working our way through college building kitchen cabinets. One job included a dumb waiter. Can't remember the details much at all except that it was larger than yours. We used a gear motor and some micro switches, but I really can't remember the details. Ours was just a plywood lined soft and we made the waiter an inch or so smaller in each direction. I ran into the son of the man that owned the house recently and he had a wonderful time regaling me with stories about how he and his friends would ride up and down in the dumb waiter. Have to admit, that never occurred to me. He must have been a little fellow.

Where are you? Now that I think of it, I have a gear drive motor that would do the job nicely. A real bargain.

Also, I like the GDO idea above.

Re: Dumb Waiter

#4

Re: Dumb Waiter

Larry Clinton Sr.

You may want to look into the "I-Drive" Garage door opener. It would be fairly simple to install as it doesn't use rails etc. It is a computer controlled drive - may want to look into the torque /drop issues as all GDO's depend on either a clutch or in the I-drives case a current sensor to insure the door doesn't trap a child or car. If the torque question is answered, you could rig up a shaft and cable drive for the I-drive fairly easily as they are a very small unit. Instead of using a spring counter balance you may want to opt for a drop weight (going down as the car rises etc.). The I-drive is "taught" the limit settings and is quite repeatable.

Re: Dumb Waiter

#5

Re: Dumb Waiter

Fred Davis

I don't necessarily have original thoughts concerning Laundry Chutes , but having been involved with several in house building in CA , here is what the building code people want out there and since it is common sense would apply anywhere.

Laundry Chutes or Dumb waiters form a fire chimney from the bottom to the top end and therefore are required to havef a 26 Ga. GI. can for a liner with a spring loaded flap or door the automatically closes after each opening.

In other words the liner is fireproof and the draft is closed at all times when not being used.

That would be a loophole for Home insurence coverage to duck though if it conducted a fire from the basement or garage to the upstairs because the code was not followed ,in this case the code that Fire Marshalls use.

FredD

Re: Dumb Waiter

#6

Re: Consider belt drive...

Glenn Madsen

The drive mechanism on my garage door is a belt drive. Quieter than a screw drive, and easy to adjust.

Just a thought.

Re: Dumb Waiter

#7

Western PA near Washington, PA

Gary Smyth

Re: Dumb Waiter

#8

Ya know....

Gary Smyth

I really don't mind playing with insurance for me but I'm loathe to play games with fire regulations especially if one of the persons involved is restricted in movement. That is something I need to address, and frankly something I will check out before I start. The shoot already exists but it may be exempt because the house is older, still, there is no way I don't check code before this begins. I'd still like to make this a project but I didn't give fire regs a thought. If I can't make it work safely I won't do it. Thanks for the suggestions to all.

Re: Dumb Waiter

#9

Re: Dumb Waiter

Dave Paine

Tracks are an option, also if the chute is completely lined, small casters on the side should work without tracks. Worked well for the Chilean miner rescue which has spring loaded small wheels.

For the lifting mechanism, consider a screw drive garage door opener. You should be able to purchase additional lengths of the screw bar. I have two of these as my garage door openers. Very quiet. My model happens to open at twice the speed of closing. For your application you could have descent be twice the speed of ascent. You will have to fudge the safety lights which need to see a beam or else will not work. You would just need to mount them on top of the box a few inches apart. A benefit of garage door based mechanism is remote or wall switch operation.

Sounds like a fun project.