Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Circle cutting jigs?

Posts

Circle cutting jigs?

#1

JL

Circle cutting jigs?

JL

I have a couple.

One I mount on my band saw. I drill a small 1/16" hole into the bottom of the board that I am sawing. I mount the board on the band saw with a clipped 4 d finish nail through the jig into the bottom of the board. Slide into the blade and start cutting. The only drawback to this one is that I do need to put a leg on it to stabilize it.

One is a router jig. I mount the router to the paddle end and have a larger nail in what will be my center. I usually have the board sitting on some scrap on my bench. I then rotate the jig and gradually lower the bit until I have cut through the board all the way around. The drawback to this one is securing the work.

For smaller circles (less than 10") I use the lathe.

I'm reasonably happy with the band saw jig - except I do have to put a leg on it. I like the finish that I get with the router jig - but it makes more noise and mess.

What other circle jigs are easy to make and use? I suppose I could mount a jig saw to a trammel - but that is sort of like the router jig.

TIA

Re: Circle cutting jigs?

#2

Re: Circle cutting jigs?

mamc

Different needs require a different jig!

I also use both and they each work very well depending on the job.

Can't say I have seen any other circle jigs that are not basically like the two you describe.

I prefer the bandsaw jig more as its a one pass process , quiet, accurate, and no risk of any tearout.

Once the piece gets more then 36" in diameter the bandsaw jig needs to be large and can get problematic so I go to the trammel jig and router for better control.

Re: Circle cutting jigs?

#3

Re: Circle cutting jigs?

Hal

Here is what may be a stupid question. I don't have a bandsaw so obviously not a circle cutting jig, but hope to have both someday. I visualize the jig and even saw Norm use one when building a round table. What I don't vizualize is how you "slide" the workpiece into the saw blade. Do you have to start ith the workpiece off the pin and then drop it on the pin when the blade is at your cut line? That could be a little tricky. As I said, may be a stupid question. Hal

PS I do use a trammel with my router, but does it ever make a mess - plus noise!!

Re: Circle cutting jigs?

#4

Re: Circle cutting jigs?

Fred Davis

For large , perfect, smooth edged circle cutting I use the Table Saw.

That be more excitement then you can stand at first , if you do it , have a helper turn the plywood into the blade while you raise it 1/8" per revolution of the stock.

FredD

Re: Circle cutting jigs?

#5

Re: Circle cutting jigs?

Jesse Cloud

If you are doing lots of the same circle or part of a circle, use your jig to cut an appropriately sized MDF pattern, then run your router with a bushing against the template, which can be taped or clamped on.

The best circle jig I ever used is made by a German company that begins with F, but if I said more, the flamers on this board would be all over me.

Re: Circle cutting jigs?

#6

JL

Re: Circle cutting jigs?

JL

"Here is what may be a stupid question. I don't have a bandsaw so obviously not a circle cutting jig, but hope to have both someday. I visualize the jig and even saw Norm use one when building a round table. What I don't vizualize is how you "slide" the workpiece into the saw blade. Do you have to start ith the workpiece off the pin and then drop it on the pin when the blade is at your cut line? That could be a little tricky. As I said, may be a stupid question. Hal "

Not a stupid question at all. The jig that I use is a 16" x 26" piece of plywood. The plywood runs from the blade out into "mid air" - so maybe 17" or so is hanging off of the table - hence the leg. I've got a hardwood runner screwed into the bottom - the hardwood runner goes in the miter gauge slot/track and is longer than the plywood is wide (maybe 24") so that I have a "handle" in the front and back. I've got a center line marked on the piece of plywood with 1/16" hole drilled every inch or so. A clipped 4 d nail (to shorten the nail) goes upward through the hole.

I drill a hole in the work piece that is NOT a through hole - but is maybe 1/3 the way in. I mount the work piece on the jig on top of the nail. I make sure that it can rotate freely. I then slide the jig onto the band saw table until the center line is where the blade begins. I rotate the work piece around the pin until the circle is completely cut. I then slide the jig off of the front of the table.

Re: Circle cutting jigs?

#8

Re: Circle cutting jigs?

Hal

Thanks, JL. Cleared up a mystery for me. Now all I have to do is get (beg) permission to buy a bandsaw. The LOML wants the round table with a lazy susan she saw on New Yankee Workshop. Maybe if I promise to build that....? Hal

Re: Circle cutting jigs?

#9

Re: Circle cutting jigs?

Stephen Kirk

Hey, that does work. But then you do have to build the piece.