Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

I'm almost embarrassed to ask this ...

Posts

I'm almost embarrassed to ask this ...

#1

I'm almost embarrassed to ask this ...

Mike in Southern NJ

I have always made a point of buying the best quality tools but yesterday I made a CraigsList purchase and found that I was a block from Harbor Freight store. On my way home, I went in to HF and looked around. Aside from their Fein MultiMaster knockoff for really little money, the only thing that caught my attention was a 12" miter saw blade. You had a choice of either 80 or 96 C3 carbide teeth, either blades selling for the whopping price of $29.99. The blade was made by the "Lifetime Carbide" brand and it was made in China, obviously.

Has anyone ever tried one of these? For 30 bucks, I may not be able to keep from trying one.

Mike who up to now has only used $75 and $120 blades

Re: I'm almost embarrassed to ask this ...

#2

Re: I'm almost embarrassed to ask this ...

DouginDenver

I have a Harbor Freight not too far from me. I can barely make myself buy anything there because everything looks so cheap - like tape measures that look like the case would shatter if you dropped it. I tried a box of their latex or whatever gloves for finsihing, figuring how bad could a latex glove be, right? They basically dissolved into the finish in seconds so I had gooey rubber in the finish and had to strip it. The only thing I own and use from them is two dial gauges I use for setting up tools. Have not been back in 3 years or so. I think I'd be scared to use a blade from them, but I'm sure others have.

Re: I'm almost embarrassed to ask this ...

#3

Re: I'm almost embarrassed to ask this ...

AZ in Colorado Springs

I have a "Lifetime" brand dado set. It was on sale for about $19, as I recall (I got it several years ago). It has two-wing chippers, and so the bottom of the groove/dado does not come out very flat, but then it was only about $19 bucks. I use it occassionally and it is still sharp.

In this case, you pay for what you get!

Re: I'm almost embarrassed to ask this ...

#4

Re: I'm almost embarrassed to ask this ...

Dave Bair, Eaton Rapids, MI

I get a good price on their 9-LED flashlight with batteries; they are free (no purchase required) with a commonly-available coupon in their circular as well as Parade mag., AARP mag. and Discover mag. I've got about a dozen so far; they will make good stocking-stuffers. I've also purchased seldom-used tools from them over the years. Their tools tend to be crude but serviceable. My latest was a wheeled hydraulic lift cart that I used to flip and move a 200-lb. table top from the workbench to the finishing stand.

Re: I'm almost embarrassed to ask this ...

#5

Re: I'm almost embarrassed to ask this ...

Jerry R

While returning from vacation a few weeks ago we got on I 95 somewhere in South Carolina heading south. Somewhere down ther road, S.C. or Georgia, cant remember, I saw a very large building and it said Harbour Freight on the side. This was a BIG building. Does anyone know what exactly they do there?

Re: I'm almost embarrassed to ask this ...

#6

HF marketing strategy...

John in NM

You can sum it up as "mights well, its sooooo cheap" :D :D :D

In some cases their stuff works ok, but I rarely find it worth bothering with the crapshoot.

Re: I'm almost embarrassed to ask this ...

#7

I have a few of there tools

Dustmaker Mike

I bought them for a one time use and I still use them. I figure if they do the job I bought them for and still work after that I did good.

Re: I'm almost embarrassed to ask this ...

#8

Re: I have a few of their tools

Gary Smyth

I use Harbor Freight tools, especially their measuring tools (an inch is an inch), impact and adjustable wrenches, magnets, hitches of various sorts and a bending tool among others. I find that they do the job and what I have bought so far is fine. I know what I'm getting into buying them so I'm careful. I too bought the 9 led lights either free or $2.98 for two and have used them for the better part of a year and so far so good. I even used one for looking at a propellor underwater. Still works. Some of their Pittsburgh Brand metal hand tools have flaked off the chrome, but so what -- they carry the same free replacement guarantee as Craftsman, Irwin, Witco, Channellock, and others (not for flaking chrome however). My name brand flea market tools are in worse shape in many instances. As mentioned, their latex gloves are thinner than those bought at a medical supply house, but all will dissolve in solvents stronger than denatured alcohol. Buy the Nitrile. I also bought little stuff knowing full well that much of the time it's a long time between uses. Why pay a premium for a tool to last several lifetimes if you or the tool manufacturer (or whoever buys them) won't honor a warranty anyway. Harbor Freight is not the place for long term, heavy duty power tools or if you have a family that will go into the 22nd century and still wants to make stuff. But if one is careful and is aware of the shortcomings, then they are at least as good as ACE and half the price. Just be a smart shopper and adjust your purchases accordingly.

Re: I'm almost embarrassed to ask this ...

#9

Don't Be Embarrassed

Mark Mandell - Gone Round In Jersey

Leave the blade on the rack. There's way more to making a good blade than carbide (c3 or whatever). How the plate is tempered and balance both before and after the carbide is brazed on will make a world of difference in the quality of the cut. If you expect a $20 blade to cut as smoothly and accurately as one costing $120, I have a bridge to sell you. It's a bit used but still serviceable. ;-}}

I do buy and use some of their pneumatic stuff like fittings, blow-guns, filter/regulators, and air hoses. The cherrypicker I put on my woodwagon does nicely as well.

While their latex gloves are junk, the Nitrile gloves are quite good and I buy a couple of boxes every year.

Re: I'm almost embarrassed to ask this ...

#10

Re: I have a few of there tools

Howard Norman

I bought them for a one time use and I still use them. I figure if they do the job I bought them for and still work after that I did good.

Agreed, I recently bought one of their air wrenches that I will use infrequently. One of my neighbors buys a lot of their tools. In fact he buys Harbor Freight tools in cases where I would not consider HF myself and seems to get away with them.

Re: I'm almost embarrassed to ask this ...

#11

Re: I have a few of their tools

Joseph Mulherin, Sr

I, too, have a few of their tools....pancake compressor which I used to spray my house in 07, also have two pin nailers which still work fine. And their compressor connectors are good too.

Also bought a scroll saw, welder and some hand tools. If they work I use them...if they break or misfunction I get new ones to replace.

Re: I'm almost embarrassed to ask this ...

#12

Steven Antonucci

I use them for "disposable" vs. renting

steven antonucci

I buy HF (or other Chinese imports) when the cost of renting a tool for a job is anywhere near buying a cheap import. I figure that the tools are good enough to get me through the job, and if I need them a second time, I have them for free.

I've never thrown away a Chinese knock-off, but go figure, plenty of Craftsman stuff...

YMMV

Steve

Re: I'm almost embarrassed to ask this ...

#13

So you're the one

DizD

who is getting all the lights. They've been out of stock the last 3 or 4 times I have gone by.

Re: I'm almost embarrassed to ask this ...

#14

Spence

Re: I use them for "disposable" vs. renting

Spence

Bought thier knock off of the Sioux drill for sanding bowls. Think I had a coupon and it was less than $20. Worked for about 2 seconds and quit so I gave it a whack and got about 4 seconds out of it. Pulled the brushes and the springs looked a bit short so I stretched them out and its worked for about 5 or 6 yeras now and a lot of bowls.

I now expect it to blow up in my hand when I use it later today. lol

Just picked up a box of the nitrile gloves and a $1.99 bench brush. So all in all I figure I'm ahead of the game. Would never buy one of their lathes or the like.

Re: I'm almost embarrassed to ask this ...

#15

Re: So you're the one

Dave Bair, Eaton Rapids, MI

I've only gotten 15 so far. My HF has broken up 2-packs of their LED lights when they ran out of the singles actually covered by the coupon.

Re: I'm almost embarrassed to ask this ...

#16

Re: I'm almost embarrassed to ask this ...

Calvin in Irmo, SC

That is near Dillion, SC and is a ditribution wwarehouse. I believe they also have a retail store on site.

Re: I'm almost embarrassed to ask this ...

#17

Those are usually worth about what you paid

Henry Higginbotham

For some reason, the Chinese manufacturers have trouble making switches that work. It's not uncommon for the included set of cheap batteries to outlast the light's ability to make electrical contact.

A notable exception (so far--knock on wood) has been flashlights made by (or branded as) Romisen. No trouble yet with a couple that are about a year old, but they cost closer to $20 each.