Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

OT - staircase railing hole "repair"/reinforcement

Posts

OT - staircase railing hole "repair"/reinforcement

#1

JL

OT - staircase railing hole "repair"/reinforcement

JL

The stairs over at the playhouse are concrete stairs. The "shaft" in which the stairs are contained has cinder block walls. The stair hand rails are coming loose in some locations.

The existing holes in the cinder block have lag shields and screws. The lag shields appear to be ~3/4" in diameter. In some places, you can pull the railing out of the wall and see the lag shields.

Obviously - they need to be fixed. I was considering larger lag shields - but as the lag shields are loose, I don't think I want to go that way. My next thought was patching with mortar or cement. I then thought of epoxy.

Right now I'm leaning towards an epoxy. Any other thoughts or better ideas? Cheap is very good.

TIA

Re: OT - staircase railing hole "repair"/reinforcement

#2

Re: OT - staircase railing hole "repair"/reinforce

George Koch

Jerome, are the handrail brackets/supports permanently attached to the handrail? If not, I would suggest shifting their location and using tapcons instead of the lead shields to reattach them. George

Re: OT - staircase railing hole "repair"/reinforcement

#3

Re: OT - staircase railing hole "repair"/reinforce

John Lucas

There is an epoxy I've used called Metal Mend (I think, it's been a while). It will take threads. I have filled in holes in concrete blocks where there was a screw anchor. I drilled the holes larger and filled it with this epoxy putty. Then I drilled it and tapped it for the screw size I wanted and reinstalled handrail that went to the basement. I lived in the house 7 more years before selling it and the rail was still solid.

Re: OT - staircase railing hole "repair"/reinforcement

#4

Re: OT - staircase railing hole "repair"/reinforce

Joseph Mulherin, Sr

Try using some hydraulic cement...it will also setup under water...the Romans used it to great advantage. Easy to work...just like regular mortar. The railing will permanetely installed and will not loosen later.

Re: OT - staircase railing hole "repair"/reinforcement

#5

JL

Welded steel

JL

Re: OT - staircase railing hole "repair"/reinforcement

#6

Re: OT - staircase railing hole "repair"/reinforce

Mark Mandell - Gone Round In Jersey

If the mounting hole was drilled into the void in the block you may consider this as a modification of John's post. Fill the void in the block with high expansion urethane foam-in-a-can through the bore hole. When it sets up hard, hollow out a space inside the foam to form a mushroom cap at least 1/2" wider in every direction that you hole. Then mix up the mechanical epoxy [Plas-steel, PC-7] or most any of the filled epoxy resins you'll find at the auto supply, pack it into your hole to fill the mushroom cap beyond and the old bore hole. When it sets well, position the railing bracket, drill and tap all the way into the interior with a course or extra course thread bold. Bolt your railing on and fhagedaboudit.

Re: OT - staircase railing hole "repair"/reinforcement

#7

JL

Thanks - John and Mark - I'll probably

JL

go this way. There aren't too many holes. I can order a large can of PC-7.

Re: OT - staircase railing hole "repair"/reinforcement

#8

Check

Mark Mandell - Gone Round In Jersey

The specs to be sure that it will take a course thread when cured and don't rush to get done. Epoxy continues to cure for a while, tap it too soon and you won't be happy.