Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

Attaching 2x4's to cinder block

Posts

Attaching 2x4's to cinder block

#1

Attaching 2x4's to cinder block

wilbur

In setting up my basement workshop, I've had a decent amount of experience attaching 2x4's to cinder block walls using Red Head sleeve anchors. I want to build a lumber rack in my garage, which is also made out of cinder block, and I plan to attach 2x4's to the cinder block in much the same way.

The problem in my garage is that the previous owners covered the cinder block with drywall. In my basement, I was careful to drill the holes for the sleeve anchors in the thickest part of the cinder block. In my garage, I have no idea where those areas are, because the dry wall covers everything.

Any suggestions on how to go about doing this without cutting holes in the drywall? If that's what I have to do, I'll do it, but I was looking for way without cutting up the drywall.

Thanks!

Re: Attaching 2x4's to cinder block

#2

JL

Re: Attaching 2x4's to cinder block

JL

As I understand it, you are attaching a 2 x 4 to your drywall covered cinder block wall to act as a vertical for your future lumber rack. I am presuming you will have horizontal members coming out from the 2 x 4 (pipe or whatever).

Do you have a "top plate" where the roof trusses meet the cinder block wall? Can you put a lag bolt through the 2 x 4 into the "top plate"? If you do this and put a few more bolts into the wall, you may not have any problems. Another alternative is some very careful measuring to try and determine where your webbing is for the cinder blocks.

Re: Attaching 2x4's to cinder block

#3

Moses Yoder

Re: Attaching 2x4's to cinder block

Moses Yoder

I think a good stud finder would work to find the joints in the cement wall, then you could go in between the joints to fasten your wood. Stud finders sense the difference in density.

Re: Attaching 2x4's to cinder block

#4

Tapcons

Bill Tindall

My brother, the builder, introduced me to these handy devices and I haven't fastened anything to masonry with anything else since.

It is not clear what the load will be on the fasteners, but if success depends on hitting the web of a cement block and not the hole, I would be looking for another design because I don't see much load bearing difference between the options. If much lumber is to go on this rack the load needs to be borne by the lumber and floor and not wall fasteners.

The simplest, most sturdy rack configuration is an "H" design where vertical members rest on the floor and the tops are fastened to the ceiling joists to keep them in place. Horizontal members bridge (bolted with 2- 1/4" bolts) between the vertical members forming an "H" or "H's". Doubling the front and back vertical pieces, and singles for the interior, and 2 x 4 horizontal pieces , an 8' high rack will carry 2-3 thousand bdft of lumber. Locate the "H's" 4' apart or put the first two closer if you are storing short lumber. Actually I prefer to keep shorts on a separate short rack.

Re: Attaching 2x4's to cinder block

#5

Clint Searl

Re: Attaching 2x4's to cinder block

Clint Searl

Use a Remington .22 nail gun and polyurethane construction adhesive and don't worry where the webs are.

Clint

Re: Attaching 2x4's to cinder block

#6

Re: Attaching 2x4's to cinder block

George Koch

wilbur, I would be very surprised if the drywall is attaached directly to the concrete block wall. See if there is wood or metal strapping/furring under the sheetrock. George

Re: Attaching 2x4's to cinder block

#7

Re: Attaching 2x4's to cinder block

wilbur

Thanks! That's an idea I hadn't considered. I'll give it a try.

Re: Attaching 2x4's to cinder block

#8

Re: Tapcons

wilbur

The sleeve anchors that I have used before and plan to use for this project are made by the same company that makes Tapcon screws. The sleeve anchors are about 20-30% stronger than Tapcons in terms of shear and tension strength.

Regardless of whether I use Tapcons or sleeve anchors, I need at least 1" of good embedment.

I do plan on supporting the bottom on the floor. I can't really attach this rack to a ceiling joist because the wall in my garage that I plan to use for the lumber rack also has a garage door rail overhead that will get in the way of tying the rack to a ceiling joist.

However, I don't need to store huge quantities of lumber. I'm only looking to store 300-400 bd. ft. at any given time, so the rack doesn't need to be that big. About 4-5' high should suit my needs just fine, so I'm hoping that floor support plus bolting the vertical supports to the wall will be enough.

Re: Attaching 2x4's to cinder block

#9

Re: Attaching 2x4's to cinder block

wilbur

You're right -- I bet there is furring underneath, but if there is, it's probably 1x3's, which I don't think would be enough for the verticals to attach to.

Re: Attaching 2x4's to cinder block

#10

no problem then

Bill Tindall

If the load is going to be borne by vertical supports sitting on the floor then the only function of the wall anchors is to keep the whole affair from tipping and that won't require much strength. I would run a long Tapcon through the furring strips and hit what ever I happened to hit in the block. I don't see any force that will apply any significant shear load.

Re: Attaching 2x4's to cinder block

#11

JL

Would probably detect the firring strips

JL

Re: Attaching 2x4's to cinder block

#12

Have you considered cutting out a bit of drywall?

Bill Houghton, Sebastopol, CA

Just a large enough chunk to measure the size - width, height - of the blocks? You could then measure over and as needed up or down to hit the webs of the blocks.

You would then have to patch the drywall, of course; but this is a garage - the patch doesn't have to meet Wife Standards necessarily.