Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

Milling Pressure-Treated Lumber

Posts

Milling Pressure-Treated Lumber

#1

Milling Pressure-Treated Lumber

Steve Bellner

I need to repair the railing on my 11-year old deck. One of the boards has split, and I noticed after all these years the railing was not installed "properly." The railing consists of a top cap and bottom rail, infilled with machined ballisters. The ballisters were attached to the top cap directly. I prefer a sub-cap, with a top cap attached to the sub from the underside. But I digress...

The original installation was probably CCA and was milled with a bottom groove and beaded edges. This product is no longer available, but it's a simple profile to reproduce from a 2x4. The wood I picked up today is ACQ-D treated southern yellow pine, and must have 20+% moisture in it. It's literally wet to the touch, and weighs a ton. How dry should I let this wood get before I start milling, and how long will it take to dry? I've got it inside at about 68 deg F. and 50% RH. Any tricks on how to keep it from twisting and bowing while it drys? I've got both ends in a press and I have a piece of angle iron clamped to the middle of four boards suspended on a pair of sawhorses.

By the way, I think what now passes for No. 2 grade would have been scrap wood a couple years ago. It took quite a bit of digging to find four boards that weren't loaded with loose knots and spikes. I haven't done deck work in quite a while, and I was very surprised at what passes for No. 2 these days. And before someone reminds me, I am aware of the precautions needed to be taken when working with treated lumber. Although I think the ACQ is probably a lot safer than the older CCA, I think it it probably still prudent to control and isolate sawdust and shavings from this wood.

Re: Milling Pressure-Treated Lumber

#2

Re: Milling Pressure-Treated Lumber

Barry Irby

Steve, Don't know where you are, but if you shop around you might be able to find a more full service lumber yard that has either KDAT (Kiln Dried After Treatment) or ADAT (Air Dried After Treatment) treated lumber in stock. There is such a yard in Richmond, Va near where I live. You would have the same issues with quality, but much less with warping because it would already be dry. Warping is THE issue with treated wood. I would have suggested you buy twice as much as you need in hopes of getting enough wood dry to finish the project. My other advice would be to buy much larger pieces. Such as 2 X 8's or even 2 by 12's and dry them and then rip them into 2 x 4's. 2x4's tend to come out of the smallest trashiest trees. Where as, almost by definition larger pieces must come from larger better trees. At least, that's my story and I am sticking to it. Cutting the stock out of larger stock may also give you some opportunity to straighten the pieces when you rip them. None of this is fool proof. The 2x4's may warp as you rip them out of the larger stock, but my experience is that this is much less than what you get when you dry them separately.

I think it will take six months to a year of more for the lumber to dry to the point it is reasonably stable. Perhaps you could buy the lumber now and do the project next spring, it may dry well over the winter.

Re: Milling Pressure-Treated Lumber

#3

Re: Milling Pressure-Treated Lumber

DizD

The old adage " you get what you pay for" still applies. The grading for SYP is for strength- not appearance. For your application a grade 1 or grade 1 dense ( nlt 6 growth rings/inch) would be a better choice. Also KDAT as mentioned. Generally found at specialty dealers, not the big boxes.

Other info offered at www.southernpine.com including a dealer locator by state.

Re: Milling Pressure-Treated Lumber

#4

Re: Milling Pressure-Treated Lumber

FredD

It shows how far the Lumber industry has declined when 6 growth rings per inch is considered #1 0r #2.

FredD