Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Tip for using a hole saw

Posts

Tip for using a hole saw

#1

Tip for using a hole saw

Barry Irby

One of the local PBS channels is running a Turning show and a Wood Working show. At 1:00 pm on Fridays. Must think we all all retired.

The Woodworking show is the product of one of the magazines and they usually have two or three guys explaining the process, what ever it is. The Scripting is so stilted it is almost funny. (Why, Yes...Dan,,, You,,,,can cut....dovetails... with a ....router. You need....a.....jig....like...this one.....) They could have twice as much dialogue, if they spoke naturally.

Anyway, they did have what looked like a good tip for using a hole saw. Lets say you are drilling into the workpiece with a 2" saw. Start the hole, marking the perimeter of the two inch hole maybe and 1/8" deep. Stop and drill a smaller hole, maybe 3/4" so that the perimeter of the two holes touch each other. A smaller hole inside a larger one. You could drill several smaller ones around the perimeter. The smaller holes give the sawdust someplace to go. It can fall out rather than packing up in the teeth. Have not tried it yet, but it looks like it would work and it looks like it might make it easier to get the plug out of the hole saw. Anybody tried this?

Re: Tip for using a hole saw

#2

Re: Tip for using a hole saw

Marv

Hi Barry,

I just lift the hole saw up out of the hole quite often and clear the teeth. When possible I will drill from both sides so the hole saw won't have to drill as deep.

The question that comes to mind is, what keeps the smaller hole saw from plugging it's teeth? :\

Marv

Re: Tip for using a hole saw

#3

Clint Searl

Wasre of time

Clint Searl

Re: Tip for using a hole saw

#4

Too many teeth is the problem

Keith Newton

Barry, many years ago I ground two of every three teeth off to enlarge the gullet. Later even 4 of 5 was even better.

While at that, I touch the front of the remaining teeth, to get rid of any positive hook. 90 or -5, will get rid of the arm-breaking snag tendency.

Try it on a dull one to experience a no risk test drive.

Re: Tip for using a hole saw

#5

Re: Tip for using a hole saw

John Lucas

That's one of those tips that someone came up with and he was really proud of it. Nobody does it of course. Takes too much time, there is a chance for error and ruining the original hole and just backing the bit out takes care of the sawdust.

Now a tip on how to get the plug out of the hole saw after it's cut would be handy.

Re: Tip for using a hole saw

#6

That's what I do too....

John in NM

The PBS show's idea sounds like an awful lot of saw changing to me... mebbe if I had two drill presses! :D

Frankly hole sawing in wood just isn't that bad for clogging - now try 1/2" aluminum! Horrible...

Re: Tip for using a hole saw

#7

Re: Tip for using a hole saw

steve mackay

Marvs right on ! I cut LOTS of wheels with my hole saws. The only part I want is the INSIDE for wheels. If your drilling holes in that "inside" its going to weaken it. That hole saw can, at times, REALLY grab hold of my work piece and start it spining like crazy. You'll breal, at least, two finger nails before you reach the off switch. And yes, those other holles will fill and pack before they "route' any saw dust out of the cut. Lifting the saw is the only way to keep the cut clear. On the other hand, for cutting anything where you want the "inside" of the saw, cut your stock to the same width as the outside of the saw. The dust will clear to the outside.

Wheel cut'n fool (80 or 100 at a batch)

Re: Tip for using a hole saw

#8

Re: Tip for using a hole saw

Marv

John,

Most hole saws I've used have holes in the top so you can poke down through them and push the plug out. If there aren't any holes, drill two or three, about 1/4" dia.

Marv

Re: Tip for using a hole saw

#9

Good idea

Marv

Keith,

Good idea to grind off some of the teeth. Adding just a tad more set in the teeth will help also.

Marv

Re: Tip for using a hole saw

#10

Re: That's what I do too....

Marv

John,

You are right about using a hole saw for drilling aluminum. It helps to use the slowest speed on your drill press and use a cutting fluid. Problem is, most drill presses don't go slow enough. The work piece should be clamped to the drill press table.

I have been successful using a fly-cutter. With a fly-cutter, you can grind the cutter with very little relief on the bottom side of the cutter. This will prevent it from grabbing and digging in too much. Also run the drill press at it's slowest speed and use cutting fluid and clamp the work piece. With a proper set up and the cutting tool ground just right, you can actually get a curl while it cuts. Different alloys will cut differently. Soft alloys are the worst.

Marv

Re: Tip for using a hole saw

#11

Soft alloys are indeed the worst....

John in NM

I believe the one time I had to do this I was cutting some of that really soft stuff like you get at the hardware store (sorry, but I'm totally lost with Al alloy #'s :D )

We've used some stuff at work that machines really nicely, not sticky at all. Anymore I just cut big holes using the mill at work, its really got me spoiled. I even use it for wood parts when the mechanic isn't around to have a fit about all the dust :D

Re: Tip for using a hole saw

#12

Re: Tip for using a hole saw

Lee Schierer McKean, PA

You don't have that problem with Forstner bits and you get a better quality hole.

Lee

Re: Tip for using a hole saw

#13

Re: Tip for using a hole saw

Marv

Lee,

You are absolutely right. I'll grab a forstner bit as long as I have one big enough. Not sure how big they make em. I have one big sucker that's about 2-1/2" but If I need a bigger hole, it's either a hole saw or a fly-cutter or maybe my sabre saw.

When I need an odd size large hole, the adjustable fly-cutter is the only way to go.

Marv

Re: Tip for using a hole saw

#14

Re: Soft alloys are indeed the worst....

Marv

Yeah, I'm aware of those machinist types :D They think of sawdust on a milling machine like lice in our hair. I use my metal lathe and milling machine for anything and everything, metal, wood, or otherwise. Sawdust is great around my machines, it soaks up the oil. :)

Marv

Re: Tip for using a hole saw

#15

Re: Tip for using a hole saw

Bill Houghton, Sebastopol, CA

Even with the holes, they can be stubborn. I finally treated myself to a Bosch set, which has a quick-release between spindle and saw (similar to, but way larger than, the spring-loaded collar on a Yankee screwdriver, or to the collar on an air hose quick-release). Removing the saw gives me a very large hole through which to pry and shove.

Its only disadvantage is that the spindle won't follow the saw through a hole in small diameters; but, so far, this hasn't been a dealbreaker.

Re: Tip for using a hole saw

#16

Easy stuff . . .

steve mackay

Wallnut pick through the side holes. Poke, turn, poke, turn, poke. Dryer the wood the quicker it'll fall out.

Re: Tip for using a hole saw

#17

Use a file card to clean the teeth.

Phil Joines

I've drilled thousands of holes with hole saws, mostly around 4". A file card's teeth are short enough they don't bend like a regular wire brush. Hold it against the side and slightly under the teeth as it turns. You can feel when they're clogged. It only takes a second or two.