Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Lumber to frame paintings

Posts

Lumber to frame paintings

#1

Lumber to frame paintings

ILYA Z

My wife paints a lot and recently asked me to make a few frames for her pieces. Her teacher told her that she makes all her frames herself using lumber that she buys at Home Depot. I went to a nearby HD yesterday looking for lumber that

1. Is 1" or thicker, preferably 4" wide

2. Without knots

3. Not too heavy

4. Not too expensive

I found some white pine boards from New Zealand but they were only 3.5" wide and 1" thick. I am not sure whether rule #2 is really essential since my wife will probably paint the frames dark. Anyway...

If you have experience making frames, what type of lumber do you use?

thanks.

Re: Lumber to frame paintings

#2

Re: Lumber to frame paintings

FredD

My Wife also paints (she taught Art ) .

The frames I make for her are generally out of Ash, Walnut and some Soft Maple.

I run a large crown mould pattern on the material and then assemble it in a shadow box type frame.

This you could do simply by buying the crown moulding ,though it will be more expensive then the lumber you describe.

If you planning a simple flat frame , then the above won't do.

FredD

Re: Lumber to frame paintings

#3

Re: Lumber to frame paintings

Tony - Memphis

Wow, my wife is an artist too. I have built a few frames for her. I mostly use poplar and paint it or gold leaf it. Polpar is nice to work with and not too expensive. I usually buy it at the local wood dealer, but I do buy some from Lowes. I've done several different designs using multiple pieces stacked with routed profiles. Lately, she's been painting on masonite - I make a poplar frame and attach the masonite to the top. For a lot of her stuff, she prefers very simple frames.

Tony

Re: Lumber to frame paintings

#4

Re: Lumber to frame paintings

AZ in Colorado Springs

I have made a number of frames, but not as wide as you're planning. I've used maple, oak, and poplar. Usually around 1" or 1.5 " thick, and about 2" wide.

I use a variety of router bits to cut the front profile, as well as the rabbet for the artwork. For gluing, it's best to have a square edge at the bottom/outside. After gluing, I sometimes cut a bevel all the way 'round at the TS. You can vary the height of the bevel among frames -- doesn't need to go all the way up to the face. Alternately, I'll sometimes roundover the back edges at the router table.

Doing this -- and varying the height and angle of the bevel, or the raduis of the roundover -- you can vary the appearance of the frame even if the profile on the front doesn't change very much.

Good luck.

Re: Lumber to frame paintings

#5

Clint Searl

Re: Lumber to frame paintings

Clint Searl

If they are going to be painted, check out the synthetic trim board material, like AZEK. HD and Lowes have house brands that are reasonably priced. The stuff comes in various dimensions and can be routed. And it doesn't have any knots.

An alternative is finger jointed poplar or pine trim boards.

Clint

Re: Lumber to frame paintings

#6

Re: Lumber to frame paintings

steve mackay

I started useing molding awhile ago. Solid sticks. I get 'em at a molding outfit so its cheap. Lately I even started goofing with crown molding to get that "deep" effect. Had some decent results. Well, decent enough to please myself anyway. And SWMBO hasn't complained yet. I'm sure this makes me a heratic in certin circles.

Re: Lumber to frame paintings

#7

Re: Lumber to frame paintings

del schisler

what tool's do you have??? The best wood is poplar. It is a paintable wood. You can stain it also. You can buy it in the ruff for less than $2.00 a bf. But it has to be planed down and rip to the size. Than cut to the length with 45 degree's and a spline if big frame's. I didn't read any other post's yet

Re: Lumber to frame paintings

#8

Re: Lumber to frame paintings

Tom Pilsbury (Chicago)

If she's going to paint the frames you might want to go with Poplar. It's easy to work and takes paint well. I've had pretty good results with staining poplar too, but I think that was just luck. Kind of hard to find poplar thicker than 3/4" at HD though.

Re: Lumber to frame paintings

#9

Re: Lumber to frame paintings *LINK*

Jim Dillon

Ilya,

Far be it from me to stand in the way of making your own picture frames, but another alternative is to purchase readymade or custom frames or complete kits from well-known internet sources that cater to photography. I have used Frame Destinations (link below) and they offer very fast service and superb packing at what I consider reasonable rates (at least compared to local framing shops). Naturally, the online vendors do not have the huge selection of the local framing shop, nor are they able to offer excellent advice for frame color/style selection based on seeing the actual painting. But it is an option to consider. I have ordered several of Frame Destination's plain wooden frame kits (as well as their metal frame kits for B&W photos) and was very pleased with the quality of the frame and finish. I see they have a wider selection available now and some come with a 7/8 or 1 inch deep rabbet which might be more painting friendly than the frames with 1/2 inch rabbets. There are several other online sources that are well-regarded, but I have no experience with them. Hope this helps.

Jim

Edited to add: I see Frame Destinations now offers canvas floater frames which are yet another option if your resident artist paints on canvas.


Frame Destinations

Re: Lumber to frame paintings

#10

Re: Lumber to frame paintings *LINK*

FredD

You mean like this Steve ?? ;-))

http://picasaweb.google.com/FredD17209/CrownMouldingUsedAsPictureStock?authkey=Gv1sRgCPSNgNWxmLXHmAE&feat=directlink

FredD


http://http://picasaweb.google.com/FredD17209/CrownMouldingUsedAsPictureStock?authkey=Gv1sRgCPSNgNWxmLXHmAE&feat=directlink

Re: Lumber to frame paintings

#11

Those ARE nice . . .

steve mackay

but I went the other way. Where those might be termed "concave" I kinda went "convex". In my twisted way I was thinking the perspective (angles & lines) of the frame focused out TO your eye rather than away into the room. Sorry . . . rather lofty ideas and over-thinking but kinda Victorian I guess. I'm into Victorian.


I might have to try "concave" one day though. Broaden my horizons !