Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

OT - water in conduit

Posts

OT - water in conduit

#1

OT - water in conduit

Bill Houghton, Sebastopol, CA

I'm pulling wire to an outbuilding through PVC conduit installed over ten years ago and recently extended to the building. I just duct-taped the buried end of the conduit when my son ran it under the sidewalk behind the house, and it's got water in it.

It won't be a hard pull - four #8 wires in 1" conduit over a 32 foot run - but should I run a rag through the conduit a few times to clear the water and dirt?

Re: OT - water in conduit

#2

Yes & No

Mark Mandell - Gone Round In Jersey

Yes, because removal of the water and extraneous flotsom will provide an extra margin of safety. Hook up a compressor to one end and a wet-vac to the other and you'll be done in about a minute.

No[t] really necessary, if you're pulling direct burial-rated cable whose jacketing won't be effected by the water over time.

Re: OT - water in conduit

#3

THHN wire

Bill Houghton, Sebastopol, CA

including an insulated ground.

Re: OT - water in conduit

#4

Re: OT - water in conduit

Justin Szeliga

Pull it clear w/a shop vac, any brand should work for that size.

Re: OT - water in conduit

#5

Why not ? . . .

steve mackay

My BIL with the 'Lectric Co. told me once that, as long as you were running a good ROMAX any moisture in the conduit would'nt matter BUT . . . I figure, as with all things woodworking ( or all things anyway), "Aim for perfect and hope for acceptable". Latter on if problems crop up you'll never have that nagging doubt that a dirty pipe might be a cause !

Re: OT - water in conduit

#6

I agree....And

Barry Irby

I agree with everyone else. Probably not necessary, but why not? You might find and cure a nasty surprise. And, I would get some lubricant for the conduit. They make special stuff for the purpose, but is you don't want to buy it or can't find it, you might pour in a little dish washing detergent. Or you could use some Astroglide or KY. According to Jeff Foxworthy if you use Astroglide, you can park a Cadillac in a bird house.

Re: OT - water in conduit

#7

Thanks, all; my variant

Bill Houghton, Sebastopol, CA

Neither my compressor nor my shop vac will fit in that particular part of the crawl space, not to mention the hauling-in hassle (full length of the house from the crawl space door).

I found a tool-dust-collection adapter at my Ace hardware store, a soft plastic that jammed quite nicely into the conduit at the pulling elbow up top and fit my 2-1/2" shop vac hose. Several minutes of blowing got it dry enough that a rag pulled through was just damp, instead of, as before, soaking.

Now cursing the box into place (just spun out a stainless sheet metal screw head; surfaced to get the Vice Grips to remove it).

This place has so many knowledgeable people; great resource, way, way beyond its woodworking knowledge.

Re: OT - water in conduit

#8

Re: OT - water in conduit

JoeW in Detroit, MI

At work we don't bother. Unless you think there may be debris in the pipe. If there is water in it now there will be water in it later. We usually pull a string in first, then pull in a piece of cord (like sahs cord size for that size wire. If you haven't bought the wire yet, consider THWN, same as THHN but more water resistant.

Re: OT - water in conduit

#9

Too late - bought the wire

Bill Houghton, Sebastopol, CA

It's possible that the water got in when the end was buried, before we finished the run. And I may have THWN - I'll have to look at it. It was what the local supplier had. At any rate, it's dry at the moment.

I was taught not to run cable in conduit, but I realize now that I could have put UF in there, since buried is buried, and maybe had some more water resistance.

Slowly, and usually too late, I learn.

Re: OT - water in conduit

#10

Sigh of relief...it's THWN

Bill Houghton, Sebastopol, CA

The pull went off fine today; thanks all.