Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

I did some tool shopping!

Posts

I did some tool shopping!

#1

I did some tool shopping!

Stephen kirk

I solved my dilemma of whether or not to keep a table saw around by getting a new table saw. For me, it's the right choice. I need speed, accuracy, efficiency.

Jet ran an amazing deal on their 3HP 50" Deluxe Xacta Saw, marking it down to $1699. I couldn't pass that up. Should be picking it up from my local Woodcraft in 10 days or so. This will be a huge step up from my old Craftsman contractors saw. We cleaned the shop over the weekend, getting my lumber rack out so I'll have more room for the new equipment.

The things I liked about the Jet were: a guard you can leave on, tool less guard, splitter and riving knife changes, dust shroud hooked to 4" port, good fence, easy table alignment. The bottom drawer and hooks for the fence and miter gauge are nice extras.

I only wish it also had a paddle switch.

Now I get to wait.

Re: I did some tool shopping!

#2

Jim DeLaney, Austintown, Ohio

Re: I did some tool shopping!

Jim DeLaney, Austintown, Ohio

Regarding the paddle switch...

I have the Shop Fox cabinet saw, which also didn't come with a paddle. I made my own, using a piece of �" baltic birch plywood, and a short length of piano hinge. Screwed the hinge to the bottom of the fence's angle iron. I cut an access hole thru the plywood so I can turn the saw on, and put a small piece of wood on the back of the plywood that aligns with the 'OFF' button. Painted it all red - just for aesthetics.

Now, I can turn the saw off easily and immediately by just bumping the paddle with my leg.

BTW, this arrangement works really well, and only took about half an hour to fabricate.

Re: I did some tool shopping!

#3

Re: I did some tool shopping!

George Colonel's Workshop-Havertown PA

Good Morning Stephen,

Congratulations are in order. I know you will really like Jet's fence.

George

Re: I did some tool shopping!

#4

Following in my footsteps

Neal in San Jose

I also started out with a Crapsman. When the Crapsman's poorly designed rip fence and a moment's inattention added up to a really bad kick-back, I decided to upgrade to a cabinet saw with a good fence. At the next tool show I jumped on a similar deal on the same saw. It sounds like in the decade or so I had mine, they tweaked the details a bit, but the bottom line is you are going to love that saw! I did exactly what Jim suggests and made a paddle switch out of a piece of piano hings and some 1/2 birch ply with a hole in it to turn it on that I could bump with my leg and turn off.

When I sold the Jet after 10 years of faithful, trouble-free service, I got nearly 100% of my original purchase price back. The fellow I sold it to is in my woodclub, and I know that he's never had anything but great service from it as well. You can stop following now if you want to - I upgraded to a Sawstop!

Neal

P.S. the piece of Melamine that kicked back is hung on the wall just behind the table saw as a constant reminder to pay attention.

Re: I did some tool shopping!

#5

Re: Following in my footsteps

FredD

Definitely a upgrade Neal , it does away with the need for a paddle switch, if you need to stop the saw in a hurry , you just stick your hand ,,,,,,,

All kidding aside ,I know you have had that saw for awhile and I am curious to whether it has discharged and you had to replace the cartridge and maybe the blade ???

FredD

Re: I did some tool shopping!

#6

Yep

Neal in San Jose

I still have all 10 fingers because my Sawstop fired as designed when I went brain-dead in the middle of a bunch of repetetive cuts and put my right index finger where it shouldn't have been. I posted about it at the time - back in late Dec. IIRC. I've taken the spent brake cartridge, still stuck to the blade, to both of the WW clubs I belong to and did a proper "Show and Tell" to hopefully remind the other folks to pay attention to hand position. The #1 question I get is could I pry the brake cartridge off of the blade and use the blade? Nope - I keep the "assembly" on a nail in direct sight of the saw to remind ME to pay attention!

Sawstop will give me a replacment cartidge if I go to their website and post about my "event", but I haven't done that yet. The retailer where I bought the saw carries replacement cartridges and I had another blade and clean underwear in the dresser, so I was able to get back to work the same day.

Re: I did some tool shopping!

#7

Free Replacement

David Yoho

I'd heard from another SS owner that if you send the fired cartridge and blade back to them they have a way to tell if it was caused by contact with human skin or not and, if so, would replace the cartridge for free. Do they still do that?

Re: I did some tool shopping!

#8

Re: Yep

FredD

I don't remember if I saw the post or not Neal , but I sure am glad your fingers surrived which caused me to think if you at any time previous,when you used just a regular TS , happen to go " brain dead" and stick some of you into the blade while it was running ?

Were you more alert before the SawStop came to you?

FredD

Re: I did some tool shopping!

#9

Re: I've gotta laugh

Chuck Lenz

First of all I don't know how or why this has ended up as a SawStop infomercial. And second I find it really amuseing that people will praise a company thats trying to shove their premium priced product down every woodworkers, carpenters, DIYers, etc. throat in this country, but yet they brush off American workers and have their products made in Taiwan. SWEET !

Re: I did some tool shopping!

#10

Re: I've gotta laugh

Stephen kirk

I don't mind a saw stop discussion. It was one of my options. However, at this point it was just too high of a price to swallow (probably over 3K by the time it's in my shop). Along came Jet with a guard good enough to leave on. If the guard is on, it's pretty hard to stick my hand in the blade. Add the riving knife and pawls to handle kickback and things are pretty safe. Good dust collection solves that problem.

I like the braking mechanism and hope that in the future it becomes more affordable. If it became cheap enough to be a standard item on most saws that would be great. Then find a way to make the brake reusable and not destroy the blade. It's still relatively new and I hope to see continued advancement over the years.

Re: I did some tool shopping!

#11

Re: I did some tool shopping!

Stephen kirk

Cool. Thanks.

Re: I did some tool shopping!

#12

Re: I did some tool shopping!

Stephen kirk

I'm really looking forward to it.

Re: I did some tool shopping!

#13

Re: I've gotta laugh

Chuck Lenz

Yeah, well I don't think we need the filthy rich and our goverment telling us what we need to do while they are sinking everybodys ship in this country but their own. There are plenty of other machines and tools in the shop that can take a bite out of you, it's just part of the enviroment if you want to be a woodworker. The day that I'm forced to buy a SawStop will be the day I hang it up, I'm allready on the verge of calling it quits.