Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

Mostly OT - "Outdoor plumbing enclosure"..

Posts

Mostly OT - "Outdoor plumbing enclosure"..

#1

JL

Mostly OT - "Outdoor plumbing enclosure"..

JL

We have reasonably mild winters up here in the North GA mountains. We get occasional cold snaps and periods where the temperature might get down to the 20s. We rarely get down below 10 degrees.

That being said, I've been asked to install a paddle operated horse "drinking fountain". I would rather not answer any emergency calls about the PVC pipe rupturing. I was figuring on mounting the waterer with a pressure treated 4 x 4 as the upright and a PT 2 x 4 as the cross piece. I was going to trench the pipe to the watering station well below the frost line (12-18").

The problem is the exposed pipe. I figure that insulating the pipe with the foam insulation isn't enough. I could possible enclose it in insulation and an outer "shell" of 2 or 2 1/2" PVC. I could also build an enclosure - say box in the pipe with the 4 x 4 as the "back wall" of the enclosure and use PT 1 x 6 and a bit of insulation to enclose the insulated PVC pipe.

Any thoughts?

TIA

Re: Mostly OT - "Outdoor plumbing enclosure"..

#2

Moses Yoder

Re: Mostly OT - "Outdoor plumbing enclosure"..

Moses Yoder

Here in the north I would use galvanized or copper pipe for the exposed upright piece so if the water freezes the pipe doesn't burst. A lot of times where practical a wire is run to the pipe with a heater for the pipe to keep it from freezing but you probably don't need to get that complicated.

Re: Mostly OT - "Outdoor plumbing enclosure"..

#3

I'd worry more about the valve...

John in NM

The valve is unlikely to survive a freeze and is going to be the weak point in the system. We have one of those for summer use and IIRC the valve body is plastic.

However, to answer the question instead of posing another, Type L copper or galvanized pipe will generally stand up to some freezing without bursting and the use of heat tape with a thermostat would be ideal. I would not use PVC as a long term installation under any circumstances, it's going to fail.

Re: Mostly OT - "Outdoor plumbing enclosure"..

#4

Re: Mostly OT - "Outdoor plumbing enclosure"..

andrew nistock

JL,

I was in the dairy industry for about 30 years and we used something very similar to the unit in the picture. From my experience the first place it would freeze was in the body of the drinking "cup". The valve that we used to use was made of brass and would take a little freezing and not break. Most of the newer ones were made of plastic and would freeze and break if you looked at them crosswise. My suggestion would be to install a heated fountain avaliable at most good feed supply stores. Andy

Re: Mostly OT - "Outdoor plumbing enclosure"..

#5

JL

OK, I'll go with copper (and brass)

JL

for the pipes and valve.

The owner has water (and a water line) to the pasture. She currently has an outdoor spigot on a galvanized riser. I don't really want to use the outdoor spigot to feed water into the waterer (hoses get chewed on and burst). She does have power to the barn - so I could use a heat tape on that riser.

I don't really want to run power out to the pasture - but I'll ask her if that's what she wants.

Thanks.

Re: Mostly OT - "Outdoor plumbing enclosure"..

#6

Clint Searl

Hose above the frost line

Clint Searl

Re: Mostly OT - "Outdoor plumbing enclosure"..

#7

Its been a Loooong time, But....

Barry Irby

I thought we had two kinds, indoor and out door. The indoor ones had the valve attached directly to the lever in the bowl. The outdoor ones had the valve located about 12" in the ground and attached by a rod. But its been forty years.

Re: Mostly OT - "Outdoor plumbing enclosure"..

#8

that is not the recommended device

Bill Tindall

Those devices are for indoor use only. Go to the local ag store or extension agent or FSA office and get a recommendation for an outdoor stock watering device. There are a variety of them depending on the critter to be watered and the number of critters. They are to be mounted on the ground on a cement pad. Depending, there may even be FSA funds to cost share stock watering if it gets critters out of a creek.