Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Movable Assembly table questions?

Posts

Movable Assembly table questions?

#1

Movable Assembly table questions?

Barry Irby

I am struggling with the small shop blues. My shop is jambed into a one car garage.

My immediate problem is that I have gotten into he habit of using the TS as a work table and assembly table. I spread Tyvek (I have a huge roll) over the TS and then do glue ups and assembly on it. So, During that process I can't use it as a TS. I have to move the glued panels off it while they cure to continue with the project. I really don't have room for a permanent bench or assembly table. Does anybody have any good ideas for one one wheels or one that folds down or perhaps one that raises and lowers? I need the magic one that disappears when not in use.

Re: Movable Assembly table questions?

#2

Re: Movable Assembly table questions?

Phil Joines

I use several 2'x4' folding tables. As long as they are the same height just use as many as the project needs.

Re: Movable Assembly table questions?

#3

JL

Re: Movable Assembly table questions?

JL

My wife's cousin has made a couple of "fold down" tables that he has attached to the garage wall studs. They are bolted to the walls so that the bolts act as a pivot point. They fold down and are out of the way most of the time. When he wants to use the tables, he pulls up and the legs come down. As I recall, they area about 3' deep when up and about 3" deep when down.

Re: Movable Assembly table questions?

#4

Re: Movable Assembly table questions?

George Colonel's Workshop-Havertown PA

Good Afternoon Barry,

Small shop=problems for all of us so blessed. I had to move out the lathe into my Neanderthal Shrine Room and my jointer into the laundry to make room for a very modest wheeled assembly table, which has shelves and storage drawers. It can also be utilized as a platform for my scroll saws and P+C omnijig. I would sorely miss the space it provides as a work surface. So one option is to move out another tool or so to create room.

I also use my old original Work Mate, and I do it on a daily basis. The top can be "expanded" even more with a sheet of 3/4" ply with a bottom cleat to grip with the tool's jaws. When not in use, the Work Mate tucks away under the extended right wing of my table saw.

George

Re: Movable Assembly table questions?

#5

Re: Movable Assembly table questions?

Marv

Those old folding Work-Mates are really handy. I've had one for about 35 years and use it a lot. I even use it for my miter saw and I've done the cleat on the bottom of a sheet of plywood also. Don't think you can buy them anymore, just a slimmed down version of the older ones. The newer, smaller ones might be ok and they probably fold up smaller.

I also use a couple of those metal folding sawhorses and lay a sheet of ply across them. Those saw horses fold up and take up very little space, even hang em on a wall.

I have an extra large side extension on the right side of my TS that I use a lot for assemble work and I have a router mounted on the underside of it.

Marv

Re: Movable Assembly table questions?

#6

Re: Movable Assembly table questions?

Gerald Gibbs

Don't ever let anybody throw out a hollow core door. One use is a cutting surface on one face. Attach cleats for saw clearance. The flip side is left smooth as an assembly table. Lay it on fold down sawhorses. You still need to clear room for the operation. If the weather is at all passable, I cut up sheet goods outside.

Re: Movable Assembly table questions?

#7

Re: Movable Assembly table questions?

Carol Reed, Strawberry, AZ

Yup, hollow core door and plastic fold-up sawhorses from the borg. Also made some 18" high sawhorses from scrap plywood. Good height for an assembly table. Gotta make a couple of 24" as well. Use hinges from the Habitat store (cheap) and a couple of hook and eye catches (like the old screen door locks from yesteryear.) Open up the horse, latch the hook and eye on either leg assembly and Bob's your uncle!

Re: Movable Assembly table questions?

#8

Re: Movable Assembly table questions?

George Colonel's Workshop-Havertown PA

Good Afternoon Marv,

Incorporating the router within a table saw wing is another space saving necessity. I have an oversized stand alone router table: a pleasure to operate, but a real constraint on room.

As to the Work Mate, mine is the 'standard" original, but I replaced the old jaws/work surface top with oversized poplar planks. Their extra length requires judicial attention to jaw clearance when opening/closing, but its worth it. One of the best tools in the shop, given by SWMBO who saw the practicality long before I did.

George

Re: Movable Assembly table questions?

#9

Re: Movable Assembly table questions?

Marv

George,

Afternoon,

Funny thing, my wife (she who is sometimes obeyed) gave me mine also. Good idea to replace the top boards. Mine are still in good condition. I have never drilled or sawed into them. They are a bit weathered and need a good soaking with BLO or some such sealer.

I was kind of encouraged to extend my TS on the right side so it would accommodate the new Uni-Fence I retrofitted to the front of the 12" Craftsman saw. The fence has a massive aluminum extrusion that spans the about 6 or 7 ft. across the front for the fence to slide in and on. The fence cost me more than the saw did. I like it but it is actually too big for my shop. I have the saw on wheels that comes in handy from time to time, but most of the time when I need to move it, for some reason there will be a pile of crap on the floor around. I finally cleaned my shop last Dec.

Marv



Re: Movable Assembly table questions?

#10

Re: Movable Assembly table questions?

George Colonel's Workshop-Havertown PA

Very Nice Shop Marv,

Looks as though you've a bit more room than I do. However, I have a lot more dust on everything. I guess it all works out with a couple sneezes.

George :)

Re: Movable Assembly table questions?

#11

Re: Movable Assembly table questions?

Marv

Thanks George,

Seems no matter how much space ya start out with, somehow every nook and cranny attracts something to fill it up. It's 18' x 32'.

Those pictures were taken last Dec. right after I cleaned the place up after about ten years of accumulating waste. Took me a week to clean it up. It's a combination metal working and wood working shop. My band saw, lathe and milling machine are meant for metal working but they do just fine for wood also.

Right now I'm building a three legged saw bench.

Marv

Re: Movable Assembly table questions?

#12

Torsion Box and sawhorses

Bill Hammond, Oregon Coast

The real question is; Is this table going to stay about or be put away when not needed?

If you plan to strike it between uses I suggest a torsion box thin enough to store over the garage door. If thick enough put some holes through between the skins that the pipe from your pipe clamps will fit through. That way you can clamp to the table edge or clamp on a raised edge when needed. Then make some folding saw horses of various heights to support the table when used. If properly made the table can be dead flat for assembling doors and the like. One side can be used to attach fixtures to and the other with a good layer of poly to make cleaning the glue up easier. Often the torsion box tables are made of MDF but that is very heavy, my large one (72" x 34") is of 1/2" CDX and I can lift and flip it by my self.

Another option, if you have seen the benches where the back folds down to make a table, the same idea can be used for a self storing table with some storage in the bottom.

Bill

Re: Movable Assembly table questions?

#13

Re: Movable Assembly table questions?

Gary Smyth


I recenty found an identical table at a yard sale. Got a great deal. Will hold three hundred pounds. Is used by salesmen to transport heavy equipment. Made by a company named Ferno, the people who make ambulance carts and it both folds down and rolls easily in an out of a station wagon or van. There is a video under "Ferno Salesmaker Stairclimber #286". Anyway it folds down and can be hung on the wall. Maybe thirty pounds. Failing this, a scissor (Harbor Freight) table works too, but it is much heavier.

Re: Movable Assembly table questions?

#14

Leo Cuellar

Re: Movable Assembly table questions?

Leo Cuellar

If your ceiling is high enough, maybe a suspended platform rigged to one of those cheap electric hoists?