Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Spray gun

Posts

Spray gun

#1

Spray gun

Gary Smyth

OK its getting to be Autumn soon with reduced temps and less humidity. I've got the itch to try something new. Spraying furniture is my thought. I've read all I can and viewed every free video I can locate. I have the desire but not the $600 for a HVLP turbine. I have a compressor that can operate a low pressure gun at about 4 to 5 psi. I want to spray stain, paint, and a clear finish. I have the luxury of time. Speed is not important. I'm not after something that is used to clearcoat autos. I have a Wagner that I used on outdoor lattice and after that experience I do not want a Wagner -- or anything turning out simiar results. I am looking for something that I won't hate a year from now, but not so expensive I'll hate myself this month. Nothing over $150 tops--TOPS! This gun will be used only occasionally, perhaps ten times on a good year. I do not need a large capacity cup, as say, a corner cupboard would be the extent of my largest project. Anyone out there have something that they like? Something they use? Something that works with acceptable results and low downtime for repair/maintenance? Is there a WoodCentral tested gun that fits my limits?

Re: Spray gun

#2

Re: Spray gun *LINK*

Mark Mandell - Gone Round In Jersey

Gary,

I have a full size pressure pot fed HVLP, but for smaller pieces and especially lathe work the CAT Mini gun just can't be beat in my book. Go to the link. $150.00 and you can get it with a bigger cup if you need that. I use mine for both shellac and waterborne top coats as well as toning and staining. Very consistent and even pattern. Comes in a kit with 3 different tip & needle sets, and 2 cups. This is my goto gun when I don't want to go through the whole deal of schlepping out the big gun to spray a cup's worth of finish.

PS: For even better control, I strongly recommend the mini regulator you'll see on their page. Gives very precise air to optimize the HVLP effect and minimize over-spray.


CA Tech mini

Re: Spray gun

#3

that one is EASY

Bill Tindall

Visit Ebay or similar source of used stuff and get a professional conventional spray gun- DeVilbiss (sp?)or Binks. Son in law got an essentially new one for $50. The cap needs to be about a #30.

There are some good reasons to not join the movement to HVLP. A conventional gun will be significantly easier to learn to use. They atomize better and are therefore more forgiving of variables that affect results. A conventional gun will be more wasteful of finish and have more over spray, but if these issues are not significant to you, by all means go conventional. I would only consider HVLP if I was needing to spray indoors. I spray outside, year around, sometimes well below freezing. After flash-off I move stuff inside, or in a van, for cure if it is very cold.

I had sprayed conventional for many years, tried HVLP, didn't see significant benefit relative to needing to be more precise in technique and went back to conventional. I have, in a pinch, sprayed conventional with a tiny portable air nailer compressor. I spray oil paint, varnish, lacquer and conversion varnish with my DeVilbiss with a #30 cap.

If you wind up liking spraying then look into the 3M PPS product. As cheap as I am I love it.

Re: Spray gun

#4

Re: Spray gun

Robert R. Clough - Thorncraft

This post brings up a question. Ok, so used is good. Now, what about the "pulse"guns. Seems to me they might be fine for poly (I cannot type tofay - keep getting words like fifne, etc and tofay.) Anyway, with proper dilution, perhaps I might find them useful.

Re: Spray gun

#5

Re: Spray gun

David Yoho

Have you looked into the Earlex Spray Station 3500 HVLP? Woodcraft sells it for $150. A friend of mine is a professional furniture maker and has used/uses probably every high-end gun during his career. He was asked to try the Earlex and came away with very positive comments and results.

I point this out because it looks like you can have HVLP at a price that fits your budget and I know it works. For the amount of spraying you will be doing, this could be an affordable and workable solution.

Re: Spray gun

#6

Jim Rahbe, Bedford Texas

Re: Another Spray Gun Option *LINK*

Jim Rahbe, Bedford Texas

Gary,

I have used Harbor Freight�s $75 self-contained HVLP system for several years and I think it works great. I use it to spray shellac and pre-cat lacquer without any issues. It will NOT spray house paint. It basically has a small turbine that pushes air through a hose to the gun. If there is an issue, it is that the air does not shut off when you release the trigger. If the unit is on, the air is on. I don�t find that to be a problem at all, but you might.

Just one of many options..

Regards,

Jim R.


$75 HVLP System