Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Cutting long 45's on TS Question

Posts

Cutting long 45's on TS Question

#1

Cutting long 45's on TS Question

Barry Irby

I am trying to make some night stands for my son and DAD's bed. they are made of walnut panels that are 18" wide. I want to miter the corners, as if I took a board and folded it in two places. These are cross cuts. Ends up very "cubic". So, how to do it? I have a right tilt table saw. yesterday, I did a practice run on some scraps. cranked the saw over to 45, and moved the fence to the left of the blade and ran both pieces. I may be wrong, but I like having the piece on top of the blade. Then I slapped a few biscuit into the joint and clamped it up. It came out at about an 89 degree angle, just under 90.

My practice pieces were short but wide, so I was able to use the fence even though they were cross cuts. My fence won't go far enough to the left to allow for this procedure on the actual cuts, but it will move far enough to the right. Should I use the fence or a crosscut sled?

It seems to me that there should be a way to do this that assures a perfect 90. Do you run one piece on top the blade and one under the blade? One flat on the table and one standing vertical? Or do you just tune the saw and have at it?

Re: Cutting long 45's on TS Question

#2

Jason Roehl in Lafayette, IN

Re: Cutting long 45's on TS Question

Jason Roehl in Lafayette, IN

So, if I understand you correctly, you want to sandwich two boards together in parallel with 45� cross-grain bevels cut on the ends such that a v-groove is formed on the ends, which would then be filled with a wedge-shaped piece to make the ends square again and make the grain appear to wrap around the end.

I'd use a router with a 45� bit.

Jason

Re: Cutting long 45's on TS Question

#3

Ellis Walentine

Crosscut sled

Ellis Walentine

This is a classic case for a crosscut sled.

Ellis

Re: Cutting long 45's on TS Question

#4

I'm not being clear....

Barry Irby

Lets, for the sake of discussion say I want to make a box or cube that is 24" square and 18" deep with mitered corners. I want to cut 18" long forty fives on the ends of all the pieces and then glue them up so that the corners are 90 degrees (square). The pieces are almost 7/8" thick, so it would take a fairly large router bit. I have a small one, but not one large enough to cut these pieces in a single pass. So, I am trying to do this on the table saw.

Seems like you should be able to crank the blade over to 45 degrees, put the pieces on a cross cut sled and have at it, but if the angle of the sled is off even a tiny amount, it multiplies out over the 18" width. And if the blade is off angle even a tiny amount, that multiplies out also. So, What can I do to cancel out the repetitive error's? Or, would you buy a bigger router bit?

Re: Cutting long 45's on TS Question

#5

Re: I'm not being clear....

Grant Wilkinson

Since I cut staves for columns on a right tilt TS, with the fence on the right (GASP), I would do the same in your application. I know that there are those that forcefully assert that what I am doing is defying death, but I like the idea that the blade keeps the wood tight to the fence, rather than trying to push it away. I use a good push stick to address kick back and make sure the splitter hold the kerf open. You likely would not have that issue with your project.

Re: Cutting long 45's on TS Question

#6

Re: Cutting long 45's on TS Question *LINK*

del schisler

I haven't read the other post's. Sounds like you need a wixey or the beall. I have the beall which i belive is better. Once you set the angle it is at that angle . No more just using the piece that is sopose to be 45 degrees or is the blade at 90 dergees or what ever degree's you want. This work's on any table to blade or even drill press . The only way to go

http://www.amazon.com/Beall-Tool-14220-Tilt-Box/dp/B001DXFFBM

http://www.rockler.com/search_results.cfm?filter=wixey+digital+angle+gauge&ne_ppc_id=google&ne_key_id=sHEYilWmN&pcrid=1168308000&gclid=CKjP25nWz6MCFRto5QodJ3c5qw


http://www.rockler.com/search_results.cfm?filter

Re: Cutting long 45's on TS Question

#7

Sled

John in NM

Be warned though, a sled is the kind of fixture you can get addicted to building and improving, ending up with 6 variations before arriving at the "perfect" sled, meanwhile your project languishes.... :D Kind of like a shooting board :D

I'd also recommend double checking your angle measurement relative to the sled when you get it built. TS tilt can be difficult to measure (like if the throat plate is a hair different than the top), and that could have something to do with being a 1/2 degree off on the test piece.

I usually spline these joints with 1/4" plywood, but that's personal preference, biscuits should be ok.

Now, if things go wrong, two things to remember.

The classic "hackinter" trick if you have an outside miter with a little gap and its already glued up and you can't or won't make another. You're probably going to run a small round over to break the edge a bit, even just 1/16", so you mash the wood fibers on the point of the miter by light taps with a steel hammer. You then swear up and down til tuesday that you will make a better miter next time :D Its actually surprising how well this one works, looks wise, so much so that having to resort to it gives you an evil little thrill like running a stop sign.

The other thing to remember is that perfect 90's are desirable for many reasons, aesthetics, pride of workmanship, ease of assembly, etc. But the piece will be serviceable even if they all turn out to be 89's. I swear once I managed to make a whole carcase with all the corners not quite 90, and some were less, some were more. All ended up tight, so it must have averaged out :D

Re: Cutting long 45's on TS Question

#8

Re: Cutting long 45's on TS Question

David Hay Denver

As others have stated, this is a good case for using a crosscut sled. If you use a two-runner design, you can account for any error in the tilt of the blade by cutting one side of the miter on the left side of the blade (outside up) and the other side on the right side of the blade (outside down). This way, any error cancels out (i.e. 44.5 deg + 45.5 deg = 90 deg)

I'd be wary of doing the miter on the right of a right tilted blade. The first cut would be fine, but when you cut the opposite end of the panel, the tip of the first miter you cut will want to slip under the rip fence.

David

Re: Cutting long 45's on TS Question

#9

Ellis Walentine

Make the sled accurately

Ellis Walentine

If the fence of your sled is exactly perpendicular to the runners (hence the blade, assuming your saw is properly aligned), you won't need to worry about the crosscut angle. That leaves you the blade tilt, which should be easy enough to get right by making a few test pieces.

Ellis

Re: Cutting long 45's on TS Question

#10

Re: Cutting long 45's on TS Question

pecker

Do it like this.

http://www.cjohnhebert.com/Bed.htm

If you don't have a digital angle gauge to measure blade tilt, make a couple practice pieces and tweak the blade angle until two bevel cuts joined together give a perfect right angle.

Re: Cutting long 45's on TS Question

#11

Leo Cuellar

Re: Cutting long 45's on TS Question

Leo Cuellar

If your saw has round fence rails, it might be possible to detach them and shift them to the left for a wider cut. I had 2 models of saw that allowed this, even had the holes drilled for it. Or they can be swapped front to back and reversed so they point to the left.