Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

Router table lifts

Posts

Router table lifts

#1

Router table lifts

Hamish

I have a hobby presses steel Bosch router table and am looking to up-grade it so that I can use larger diameter cutters to make kitchen cupboard doors etc. These cutters are 89mm in diameter, which are too big for my current table. I am intending to make my own table, rather like the Colonel's, and am thinking about incorporating a router lift, like the following: http://www.axminster.co.uk/axminster-the-axminster-router-elevator-prod808144/ which has a hole diameter of 92m and a lift of 90mm.

Does anybody have any opinions about these?

Thanks Hamish

Re: Router table lifts

#2

Re: Router table lifts

George Colonel's Workshop-Havertown PA

Good Afternoon Hamish,

One upgrade which I will make to my latest router table is a "T"-track running across the width of the top, primarily to mount feather boards. Otherwise, I have been satisfied with the operational portion of the table design. I suggest you pay particular attention to the evacuation of dust.

I presently use a 2 1/2 inch aperature ported commercial aluminun split fence (Penn State Industries), and connect my shop vac hose to that. DC from the fence is most effective. I have a large hooded vent mounted to the inside of the cabinet back, and it has a 4 inch opening connected to my DC plumming. It isn't as effective as my previous table which incorporated a plenum at the rear of the cabinet, around which dust was drawn to the back exhaust port.

As to the lift mechanism, the Axeminster chain drive may be affected by dust accumulation, and represents another reason for good cabinet design. In fairness, my JessEm Mast R Lift has remained easy to raise and lower, given frequent sweeps with a vacuum nozzle. It is prudent to vacuum any lift mechanism anyway.

I certainly agree that a mechanism premitting above table bit height adjustment is a beneficial improvement for all light/medium weight routers, and a necessity for the heavy weights. They decrease the work and set-up time, and increase the fun and quality of cut.

Please post a pix once your set up is made. Good Luch,

George

Re: Router table lifts

#3

Re: Router table lifts

Jerry Gibbs

Why would I buy a $250 router lift when I can buy a new router with a built in lift mechanism? I don't have either.

Re: Router table lifts

#4

Re: Router table lifts *LINK*

Dave Paine

I am in the US so no experience of the UK manufacturer. I do have experience with a US equivalent. Link included.

Initially I did not know if the dust would clog up the mechanism, but it did not. I do however have a router table with a 4 inch dust collector hose attachment. I get very little dust remaining after any use, just in the corner dead zones.

I purchased a router table top, happens to be from the same Woodpeck site and made my own router table with a lot of attention to dust collection.

I later moved onto a different lift from the same site. I debated another lift to use with my Bosch 16176EVS router, or purchase a new router with built-in lift. I ended up wanting the ability to quickly drop the router beneath the table since I often use my router table as a work surface for gluing etc.

I have an Incra fence. Both Incra and Jessem make excellent fences. Both allow moving the fence in 1/32inch increments. Very easy to setup or reproduce a setting. Give such a fence consideration. Prior to the Incra I had the normal "nudge and clamp" arrangement. Took me ages to get the fence just right, and if I later had to re-create the operation due to a piece needing to be replaced, it took even longer.


http://www.woodpeck.com/unilift.html

Re: Router table lifts

#5

Re: Router table lifts

FredD

George, you are taking all of the fun out of lifting a 3 1/4 HP router out of the top and struggling with a bit change and height adjustment for each job.

The pain of it all in the right perspective is to be looked forward to.

Not to mention the knots accumulated on my bald pate when I painfully bend over with my Arthritic back and crack my head underneath the table while skinning my knuckles loosing the Router motor lock in the too small space I allowed for it , when I made the damn thing.

The language employed in the process you would not find in a owners manual ;-))

FredD