Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

brush cleaner

Posts

brush cleaner

#1

brush cleaner

Gary Smyth

Today a friend used my best gold stripe paint brush then left it in a can of latex paint. When I found it it had been in the sun for a couple of hours and caked to within 1/2" of the ferrule. I've washed it and wire brushed, combed, and washed some more. It's useable, but nothing like it was yesterday. I'm not going to ask him to replace a $50 dollar brush. Any thoughts as to how I might eliminate some of the more persistent paint attached to the natural bristles? Would soaking help?

Re: brush cleaner

#2

Clint Searl

He owes you a new brush

Clint Searl

Re: brush cleaner

#3

Stephen Shepherd

Soak it in alcohol

Stephen Shepherd

Re: brush cleaner

#4

I've used lacquer thinner and a comb...

John in NM

To clean up that sort of problem, soaking in a shallow pan with the handle resting on the edge of the pan. The solvent and combing might damage the brush though, be warned. I'm not overly fussy about lending tools, but the world at large seems so inept when it comes to cleaning brushes, that I'll never lend one that I'm not prepared to replace.

Re: brush cleaner

#5

Re: I've used lacquer thinner and a comb...

Jerry Gibbs

I've used ordinary store bought brush cleaner with success. the cleaner can be re-used, but you lose some every rime.

Re: brush cleaner

#6

Vent. I'm about to spit bullets.  Can

Gary Smyth

you believe this? Today the same neighbor came asking to use the same brush he used yesterday. He said he liked the way it felt. We had a discussion. I told him that the brush was an expensive one, perhaps the best I own, and that he left it in the paint yesterday and then walked away and did other things. His response. "I got busy." -- And (with an incredulous smile) why would ANYONE spend that much for a paint brush. As my eyes turned red I asked him why he wanted that brush again and he said that it had lots of bristles, held paint, and worked the paint well. I then proceeded to show him what the brush looked like even after my efforts to clean it. He said he was sorry, (steady now) but could he still use it as it looked OK to him.

I asked him to look elsewhere and he looked at me as if I didn't want to be a good neighbor. I like the guy, we get along fine until now but either he truly doesn't understand, or doesn't have an inkling of the (my) value of good, well cared for tools. Now I have two problems. A angry neighbor and a semi stiff brush. I'd like to fix them both but I'll settle for the latter. I'm taking suggestions.

Re: brush cleaner

#7

Re: brush cleaner

Mark Mandell - Gone Round In Jersey

I use regular brush cleaner for that situation (Paint store - several brands). Use metal or glass container just big enough to hold the brush then put in enough cleaner to just reach the ferrule. Let sit overnight, comb out, then brush out any remaining junk and particles. Re-immerse with clean solvent for another 8-10 hours. Haven't gotten anything in a brush that this stuff won't take out. It's a mix of several kinds of solvents (ventilation required) and leaves the natural bristle brushes supple and clean.

Not for nylon or other synthetics, however; they melt. :b

Pour the used cleaner into a lidded jar, cap, and allow it to settle out. Pour off the clear liquid and use that (several times) as the first soak; saves on solvent.

Re: brush cleaner

#8

Help on both fronts

bill tindall

1. Never loan this person anything and presume in all interactions he will be clueless. It needs to be a consistent, blanket no loan policy to avoid continued risk of annoyance.

2. As I understood the situation it was latex paint. You may be in luck. Many latex paints are not crosslinked when they cure. Those that aren't will be soluble in a few solvents. If you have lacquer thinner try that, but a ketone solvent will be better. If all else fails work a methylene chloride paint stripper into the bristles and then comb out the gunk.

Technical: If a finish crosslinks it will not be insoluble in any solvent. Solvents may swell and soften the material, but it will never dissolve. Styrene, poly(vinyl acetate)( PVA) and acrylic polymers (the stuff latex paint is made from) are readily dissolved in solvents like MEK, as well as methylene chloride, which is an excellent solvent for most polymers.

You have my sympathy. I like to buy good brushes and take care of them. My favored paint brush is a 4 incher I bought in 1971. It has applied gallons of paint and seems none the worst for it. And I have a cherished varnish brush that has done acres of floors. Again, it is still in near perfect condition.

I loaned a neighbor my wheel barrow in 1988 and it still has concrete clinging to its insides.

Re: brush cleaner

#9

are you sure

bill tindall

Nylon and polyester, the stuff most synthetic bristles are made from, are only soluble ("melt" as you say) in a few exotic solvents. The most common solvent for these polymers, hexafluoroisopropanol, costs hundreds of dollars per liter and dissolves flesh. I can't imagine a solvent mix that would be safe to sell to consumers that would dissolve a nylon brush.

Some cheap brushes are made from acrylic fibers and they will dissolve in many solvents.

Re: brush cleaner

#10

Re: brush cleaner

Howard Acheson

I'm sitting here reading the label of my can of "Kleen-Strip" Roller and Brush Cleaner. It says, "Restores natural or nylon hard brushes. Washes away oil or latex paints, varnish."

I've never seen a brush cleaner that couldn't be used on synthetic bristled brushes. Over the years I've used a number of different brands. I believe that the "kleen-Strip" brand is sold at Home Depot.

Re: brush cleaner

#11

Re: brush cleaner

FredD

Animal hair brushes and water base finish (lLatex Paint) are not compatible.

The water swells the bristles and consequently the Ferrule permanently and it will soon shed hair like a Cat.

A good rule to follow on loaning tools is the same as you use on loaning out your wife.

FredD

Re: brush cleaner

#12

Re: brush cleaner

Barry Irby

I was wondering about this. Finishing, and all the variables that go into it are not my strong suit. I really don't even know enough to be dangerous. Come to think of it, the dangerous part is what I don't know. But, I thought natural bristle brushes and latex were not for each other. I thought latex paint gave natural bristle brushes a bad hair day.

Re: brush cleaner

#13

Jason Roehl in Lafayette, IN

That's the way I roll (or brush in this case)!

Jason Roehl in Lafayette, IN

Unless it's just an absolute emergency on my part, natural bristle brushes don't see waterborne finishes ever. Even for oil-based finishes (which I very, very rarely use), I typically use a nylon/polyester blend. Heck that's almost exclusively what I use. Once in a while if I have to do a trim package by hand, I might pick up a 100% nylon for the softer bristles and better overall finish, but that also depends on how thick the paint is. If it's very thick--and many paints are trending that way to meet VOC requirements--then softer bristles don't work as well. They just can't hold the weight of the finish.

I agree with the suggestion to use brush cleaner, though. It's about $10/gallon or so, and is just a nice little solvent cocktail that will at least soften most common finishes if not outright dissolve them. Like someone else said, let it soak in the brush cleaner overnight, up to the ferrule, but suspend it if possible rather than letting the brush rest on the bristles. Wash it, scrub it, comb it out, then repeat the process, making sure you get the brush cleaner worked into it up near the ferrule.

In my case, I like a good brush as much as the next guy, but it's not always worth my time to deal with them if they get too nasty. I don't want to think too much about what I've spent on brushes over the last 15 years. The number easily surpasses 4 digits.

Jason (painter by day...and sometimes, night).

Re: brush cleaner

#14

(Message Deleted by Poster)

Chuck Lenz

Re: brush cleaner

#15

In my case it was a Dr.

bill tindall

However, he was in charge of the emergency room at local hospital and with two injure prone kids he came in handy. We never waited.

Re: brush cleaner

#16

ya gotta ask - is that the hill I wanna die on?

Tim Greif - West of Chicago

I know, you've been taken advantage of and offended, but this guy is your neighbor, right? How much do you want to have to suffer living next door to to a problem neighbor relationship? I can assure you, things can get ugly enough with the right people that you may gladly give up that $50 (brush loss) to turn back the hands of time to before the incident. I suggest you write this off as the price you pay for keeping the peace with a dumbass neighbor.

Of course, some people will take the other approach and remain bristled enough to hold the grudge "just to show em". Those people tend to be stressed and angry most of the time.

Your call.

Re: brush cleaner

#17

Gotta agree.

John E in SC

Go over and give him the brush (let him worry about trying to clean it the rest of the way), explain to him how to properly care for a good brush, and go out and buy yourself a new one with the resolve to never lend it again (your neighbor shouldn't have to ask - he has one now!) Then just let it go. In my mind, $50 just ain't worth hard feelings with a neighbor (but I wouldn't let him borrow anything else!)

Re: brush cleaner

#18

Re: brush cleaner

Mark Mandell - Gone Round In Jersey

"badda-bum-m-m ting"