Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Bed Construction/Strength Question

Posts

Bed Construction/Strength Question

#1

Bed Construction/Strength Question

Nat Robison

I'm building my son a 4-ft. high loft bed. What supports the bed is a rectangle of 2x6's with plywood screwed to the top. I'm changing it up a bit and using 2x8's with a groove/dado in it with the plywood in the groove so it forms a bit of a tray for the mattress to sit in.

Since we traded in our SUV lease and I took over a 4-door sedan, buying wood is a bit of a challenge. It might not be possible for me to get a sheet of ply home even if they cut it to rough dimension at Lowe's.

Would 1x6 or 1x8 (run perpendicular to the mattress) be sufficiently strong to support the bed and/or if I run some 2x4 "joists" under the planks? Or should I just find a way to get the ply home?

Re: Bed Construction/Strength Question

#2

Re: Bed Construction/Strength Question

woodenleg

I built a set of bunk beds for my 2 boys. I used 2x6 for legs, 1x6 for bed side rails and placed a 1/2 soft metal angle iron to hold the 1x4's to hold the mattress. We have a picture of 17 kids on the top bunk. I don't think that plywood will be needed. Dave

Re: Bed Construction/Strength Question

#3

Re: Bed Construction/Strength Question

Bruce, a MN Galoot

I would think that 1X6 or 1X8's would be overkill. By comparison I've made four queen-sized beds using 5/4 X 8 outside rails with 4/4 X 4 (yup, a full 1" thick) ash (cheapest I can find locally) spaced 1" apart spanning from side to side. That's 60" and I've never, ever had a problem.

The mattress supports that are sold at Ikea or International Design Centers make me wonder a bit. IIRC, they seemed to be about 1 X 2 maple 1/2" thick, but supported by a "joist" in the middle.

Re: Bed Construction/Strength Question

#4

Re: Bed Construction/Strength Question

John Lucas

I helped my son build one (his first woodworking project). We used 1x4's. He's 21 and about 5'10 but skinny. It's been plenty strong enough. I think we ran about 6 total.

Re: Bed Construction/Strength Question

#5

Got it.

Nat Robison

The collective wisdom is that the slats should be fine. I only mentioned 1x6 and 1x8 as a way to buy fewer boards......sounds like 1x4 should be fine. I should add that there's no boxspring in this set up so I probably won't have too many gaps between the slats.

Hopefully, he can take it to college in a few years. Thanks for the input.

Re: Bed Construction/Strength Question

#6

Re: Got it.

Bruce, a MN Galoot

One more thing. Be sure to screw down the ends of at least a couple of the slats so that the rails don't spread. BTDT, and it's a big surprise to someone.

Also, don't let any mattress salesman say you NEED a box spring. Nope.

Re: Bed Construction/Strength Question

#7

Re: Got it.

Glenn Madsen near San Francisco

We built some bunks for a city camp last week, of tulip poplar. Side rails were 5" wide 5/4, and the cross slats were 6" wide 4/4, spaced 3" apart, and screwed down.

Some of our club guys were on the upper bunk, three at a time. Pray you never have children that size. The bed, however, never even complained.

These were designed to meet some federal guidelines that one of our people had handed to him. Then he designed conservatively from there. There should be no problems whatsoever with strength.

Re: Bed Construction/Strength Question

#8

Bed slats

Hamish

We were given a IKEA bed by friends and the slats are all stapled to two webbing strips, running next to the side rails, that connect their outsides ends, effectively maintaining an equal distance between them. They are not screwed down but are held in place by 4 pieces of dowel, two at each end of the bed, that protrude about half an inch above the surface of where the slats lie, holding the furthermost slats in place. When it comes to dismantling the bed, the slats just roll up. As is typical with IKEA design, it is really very simple but effective.

Hope this will give you another idea to think about.

Cheers, Hamish.